User manual LACIE P9220 QUICK INSTALL

[. . . ] ESD Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Rack System Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Preparation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Before removal/replacement of a PSU disconnect all power for isolation. A faulty PSU must be replaced with a fully operational one within 24 hours. CAUTION: If this equipment is used in a manner not specified by LaCie, the protection provided by the equipment may be impaired. IMPORTANT INFO: The enclosure top cover must be secured, when the enclosure is in normal use, by rotating the lock 90° to the `locked' position. This is to prevent users/operators from accessing the service areas. 2. Before You Begin Before you begin, make sure the site where you intend to set up and use your enclosure has the following: Standard power from an independent source or a rack power distribution unit with a UPS. Power Cord Rack kit (if installing within a rack) CAUTION: The RJ45 sockets on the motherboard/PCI cards are for Ethernet connection only and must not be connected to a telecommunications network. IMPORTANT INFO: Do not remove covers from the PSU. Return the PSU to LaCie for repair. Refer to LaCie for a list of qualified accessories for use with the enclosure. The Accessory Box contains the power cords and other ordered accessories. IMPORTANT INFO: Bifurcated power cords must NOT be used with the 12big Rack Storage Server. LaCie Quick Install Guide 3 2. 2. Inspect the packaging for crushes, cuts, water damage or any other evidence of mishandling during transit. If any damage appears present, photograph the packaging before opening, for reference. Mounting the System into a Rack NOTE: The rail kit is suitable for 19" racks with square and round holes only. The minimum distance between vertical rack posts is 24" (610mm); the maximum distance is 36" (914mm). IMPORTANT INFO: Do not remove covers from the PSU. Check for damage, especially to the rear connector on the PSU. Handle the PSU carefully and avoid damaging the connector pins. Do not install the PSU if any pins appear to be bent. Push firmly until a click is heard as the securing spring engages. NOTE: This module must only be removed by service personnel. You are now ready to connect the power supply cords to the power sources and switch the power supply ON. Figure 4a: Removing a PSU Figure 4b: Removing a PSU LaCie Quick Install Guide 5 3. 5. Replacing a Fan IMPORTANT INFO: The cover must only be opened by service personnel. Release the enclosure top cover by turning the lock mechanism to the `Unlocked' position and slide the cover back until it stops (see Figure 5). 3. Do not install it if there are any visible signs of damage. [. . . ] Follow the steps in the Set Up Windows wizard, then log on as an administrator. Password: LaCie12big (case sensitive) 3. Start LSI MegaRAID management software from start menu or desktop. Select your server and click Connect. CAUTION: Migrating a RAID cannot be stopped and will disable any other RAID operations during processing. [. . . ]