User manual LANIER IS760D

[. . . ] Quick Installation Guide Please read the Safety Information in the Operating Instructions before using this machine. It contains important information related to USER SAFETY and PREVENTING MACHINE PROBLEMS. Image Scanner Confirming the Installation Environment Checking the Contents of the Box Check the contents of the box according to the following list. If one or some items are missing, please contact your sales or service representative. Quick Installation Guide (this sheet) CD-ROM Power Cord Tool Cleaning Cloth Safety Instruction Sheet Two Caps Installing the Scanner Remove the tape. Installing the TWAIN/ISIS Driver Preparation Log on to the computer as a member of the Administrators group, for installation to Windows 2000/XP, Windows Server 2003, or Windows NT 4. 0. This machine can be used both as a TWAIN scanner and an ISIS scanner. [. . . ] The USB and the optional IEEE1394 connection cannot be used when the SCSI synchronous transmission is set. 2 A Open the cover of the switch box on the lower left of the frontside of the scanner. ADC015S Note Push the knob of the cover to the left and pull the cover to open. B Set the DIP Switch No. 2 to the OFF position. ADC079S SCSI synchronous transmission is enabled. Note Press the Hard Reset Switch if you changed the DIP Switch while the power is ON. p. 34 "Using the Hard Reset Switch" 27 Setting up the Scanner Connecting with USB Interface Note Please use the recommended USB cable. Using other cables might occur an irregular operation. As for the recommended cables, please ask your service representative. You can connect the scanner to two computers at the same time. One with the SCSI interface, and one with the USB 2. 0 interface. Though, you cannot use the scanner at the same time from two computers. Interfaces are switched automatically when you change from one of the computer to the other. 2 A Open the cover of the switch box on the lower left of the frontside of the scanner. ADC015S Note Push the knob of the cover to the left and pull the cover to open. B Confirm the DIP Switch No. 2 is in the ON position. ADC080S Note If the DIP Switch No. 2 is set to OFF, set it to ON. If the switch is set to OFF, "Found New Hardware Wizard" will not start. . Press the Hard Reset Switch if you changed the DIP Switch while the power is ON. p. 34 "Using the Hard Reset Switch" 28 Connecting to the Computer C Connect the USB cable to the USB connector. 2 ADC022S D Connect the other side of the cable to the USB connector on your computer. Connecting with IEEE1394 Interface Note The optional IEEE1394 interface board is required. An IEEE1394 cable is packed to be used for the optional IEEE1394 interface board. An irregular operation might occur for the IEEE1394 interface board of some PC. Please use the recommended IEEE1394 interface board for your PC. As for the recommended boards, please ask you service representative. You can connect the scanner to three computers at the same time. One with a SCSI interface, and two with the optional IEEE1394 interface. Though, you cannot use the scanner at the same time from three computers. Interfaces are switched automatically when you use any one of the computers. A Open the cover of the switch box on the lower left of the frontside of the scanner. ADC015S Note Push the knob of the cover to the left and pull the cover to open. 29 Setting up the Scanner B Confirm the DIP Switch No. 2 is in the ON position. 2 ADC080S Note If the DIP Switch No. 2 is set to OFF, set it to ON. If the switch is set to OFF, "Found New Hardware Wizard" will not start. . Press the Hard Reset Switch if you changed the DIP Switch while the power is ON. p. 34 "Using the Hard Reset Switch" C Connect the IEEE1394 cable to the IEEE1394 connector. ADC023S Note Connect the cable to either one of the connectors. D Connect the other side of the cable to the IEEE1394 connector on your computer. E Repeat Steps C and D with the other IEEE1394 connector to connect with a second computer. 30 Connecting to a Power Source Connecting to a Power Source This section explains how to connect this machine to a power source, using a bundled AC power cord. R WARNING: · Do not use with a power source with a voltage different from the specified voltage. Do not use a power outlet with multiple devices plugged in. [. . . ] You can set the photo part alone as the para-intermediate (gray) tone. For an original mainly occupied by photos, to the contrary, you can detect and scan the original as a whole as the para-intermediate (gray) tone, setting the text part alone as non-intermediate (gray) tone. The maximum number of ranges to have partially different setting from the overall setting is 4. 6 IEEE1394 Interface Unit Type IS760 You can connect your PC to the IEEE1394 Interface board Two IEEE1394 connectors are available, and you can connect a total of 3 PCs to this machine together with another SCSI connector equipped. Limitation The pre-installed USB 2. 0 interface board is to be used exclusively. Note You cannot use simultaneously two or more PCs connected. [. . . ]