User manual LEICA HDS7000

[. . . ] HDS7000 User Manual Version 1. 1 English HDS7000, Introduction 2 Introduction Purchase Congratulations on the purchase of a HDS7000 instrument. This manual contains important safety directions as well as instructions for setting up the product and operating it. Refer to "6 Safety Directions" for further information. Read carefully through the User Manual before you switch on the product. Product identification The type and the serial number of your product are indicated on the type plate. [. . . ] In attributes the field Source IP address automatically and Source DNS address automatically should be checked. Settings on the HDS7000: • Switch on the HDS7000 (press the ON/OFF button for 0. 3 sec). • Go to Main Menu, Settings and enable DHCP Server. Settings on the notebook: On the notebook you can access the data on the HDS7000 using the web browser or an FTP client: • Enter the IP address of the HDS7000 into your web browser: http://<IP> or • Enter the IP address directly at the FTP client. The scan files on the HDS7000’s hard disk are listed in their subfolders in the web browser/FTP client. When using the web browser a preview of every scan is shown. You can open the scan files or download them to your notebook. HDS7000, Scanning 97 HDS7000, Scanning • • • 98 The firewall of the notebook should be deactivated to avoid disturbing the connection to the scanner. The proxy settings of the web browser should be deactivated or an exception for the web page must be declared. Enter user name “scans” for establishing an FTP connection to be able to delete scans. Backup all important files before deleting. Deleted files cannot be restored. 3. 12. 3 Access Connecting the HDS7000 by Wi-Fi Select Main Menu, Settings . Description Configuration of the laptop In the Settings menu enable the Wireless option for a Wi-Fi connection. Go to Start, Settings, Network Connections. In the Wireless Network Connections list the HDS7000 is listed as hds7000xxxx with xxxx = serial number. If scanner is not listed select Refresh network list, after some seconds the system automatically will find the HDS7000. Open your web browser and in the address field enter the Wi-Fi IP address http://192. 168. 3. 1 In Wi-Fi mode the general IP address 192. 168. 3. 1 is used instead of the unique scanner IP address. Web browser settings HDS7000, Scanning 99 HDS7000, Scanning 100 3. 13 Start page Operating the HDS7000 using a Web Browser The HDS7000 can be operated via Ethernet connection or via Wi-Fi in a local network directly using a web browser. Enter the IP address of the HDS7000 into the address field of your web browser. Refer to IP address under "3. 10 Settings". The functions of the main menu are displayed. For example: http://172. 20. 0. 100 Fixed address for Wi-Fi: http://192. 168. 3. 1 The buttons on the left side of the screen guide directly to the following menu items: • Scan • Info • Scanmanagement • Status • Help • Scan predefined If the IP address is extended to show the menu’s shortcut commands, you can go directly to the desired page. For example: http//172. 20. 0. 100/info Further shortcuts for menu points include: • • • • • • /home /info /scan /scan/predefined /scanmanagement /status • • • • • /config (password protected) /debug /firmware /camera /systemtest • • • • • • /report /backlight /profiler /statistic /error /error/help HDS7000, Scanning 101 HDS7000, Scanning Scan menu in web browser For example: http//172. 20. 0. 100/info 102 The settings for the web browser scan interface are the same as for the interface of the onboard display. Refer to chapter "3. 6. 3 Scan with User Defined Settings" for details. HDS7000, Scanning 103 HDS7000, Troubleshooting 104 4 HDS7000 Troubleshooting Problem Instrument does not boot. Possible Cause(s) Suggested Remedies Disconnect from AC power supply or external battery. [. . . ] Please make sure, that at any time you fully comply with the terms and conditions of the Leica Geosystems Software Licence Agreement. Such agreement is provided together with all products and can also be referred to and downloaded at the Leica Geosystems home page at Software Licence Agreement http://www. leica-geosystems. com/swlicense or collected from your Leica Geosystems distributor. You must not install or use the software unless you have read and accepted the terms and conditions of the Leica Geosystems Software Licence Agreement. Installation or use of the software or any part thereof, is deemed to be an acceptance of all the terms and conditions of such Licence Agreement. [. . . ]