User manual LEICA TPS400 VERSION 2.1

[. . . ] Leica TPS400 Series User Manual Version 2. 1 English Electronical Total Station Congratulations on your purchase of a new Leica Geosystems Total Station. This manual contains important safety directions as well as instructions for setting up the product and operating it. Refer to "Safety Directions" for further information. Read carefully through the User Manual before you switch on the product. Symbols used in this manual The symbols used in this User Manual have the following meanings: DANGER Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. [. . . ] More information on Hz-collimation can be found under "Adjusments". Auto-OFF Enable The product is switched off after 20 minutes without any action (= no key pressed; V and Hz angle deviation ±3' / ±600cc). Disable The product is switched on permanently. product is recovered by any key stroke. Min. Reading The displayed angle format can be selected in three steps. · For 360°'": 0° 00' 01" / 0° 00' 05" / 0° 00' 10" Always " are indicated. · For 360°: 0. 0005° / 0. 001° / 0. 005° · For gon: 0. 0005 gon / 0. 001 gon / 0. 005 gon · For mil: 0. 01 mil / 0. 05 mil / 0. 10 mil Input method Here you can select the method to input alphanumeric characters. · Method 1 Standard method · Method 2 Advanced method TPS400-2. 1. 0en 80 Settings Angle Unit °'" (degree sexagesimal) possible angle values: 0° to 359°59'59'' DD (degree decimal) possible angle values: 0° to 359. 999° gon possible angle values: 0 gon to 399. 999 gon mil possible angle values: 0 to 6399. 99mil The setting of the angle units can be changed at any time. The actual displayed values are converted according to the selected unit. Distance Unit meter Meter ft-in1/8 US-feet-Inch-1/8 inch US-ft US-feet INT-ft International feet Temperature °C Degree Celsius °F Degree Fahrenheit Pressure mbar hPa mmHg inHg Millibar Hecto Pascal Millimeter mercury column Inch mercury column Settings 81 TPS400-2. 1. 0en EDM Settings The EDM-settings contain a detailed menu with selection boxes. EDM Mode With TCR products different settings for measurements with visible (RL) and invisible (IR) EDM type are available. Depending on selected measuring mode the selection prism types are different. Fine measuring mode for high precision measurements with prisms (2mm + 2 ppm) Quick measuring mode with higher measuring speed and reduced accuracy (5mm + 2 ppm) Continuous distance measuring (5mm + 2 ppm) Distance measurement using Retro targets (5mm + 2 ppm) IR-Fine IR-Fast TC400Z74 IR-Track IR-Tape TPS400-2. 1. 0en 82 EDM Settings RL-Short Short range. For distance measurements without prisms with a target distance up to 80 m (3mm + 2 ppm) Continuous distance measurement without prisms (5mm + 2 ppm) Long range. For distance measurements with prisms (5mm + 2 ppm) 360° prism GRZ4 +23. 1 RL-Track 360° Mini prism GRZ101 +30. 0 RL-Prism With the RL-EDM each object in the beam is measured (possibly also branches, cars, etc. ). Prism type Calling the function in the EDM settings. Leica Prisms Standard prism GPH1 + GPR1 Constants [mm] Miniprism GMP101/102 JPMINI Reflective targets USER +17. 5 +34. 4 Mini prism +34. 4 is set at "Prismconst" -- (-mm + 34. 4; e. g. : mm = 14 -> input = -14 + 34. 4 = 20. 4) +34. 4 Reflectorless 0. 0 RL EDM Settings 83 TPS400-2. 1. 0en Prism Constant Calling the function in the EDM settings. Entry of a user specific prism constant. Limit value: -999 mm to +999 mm Laser Pointer Off: Visible laser beam is switched off. On: Visible laser beam for visualising the target point is switched on. Guide Light The person at the prism can be guided by the flashing lights directly to the line of sight. The light points are visible up to a distance of 150 meters. This is useful when setting out points. TC400Z75 1) Flashing red diode 2) Flashing yellow diode Operat. range: 5 - 150 m (15 -500 ft) Divergence: 12 m (40 ft) at 100 m (330 ft) TPS400-2. 1. 0en 84 EDM Settings [SCALE] Scale of projection. [P/Temp] Input of atmospheric parameters. [. . . ] 132 Tie Distance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 Tilt Correction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77 Tilting axis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Tilting axis height . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]