User manual LEICA Z16 APO

[. . . ] Leica Z6 APO Leica Z16 APO User Manual General Instructions Safety Concept Before using your macroscope for the first time, please read the "Safety Concept" brochure included with your instrument. It contains additional information about handling and care. Use in clean rooms The Leica Z series can be used in clean rooms without any problems. Cleaning Do not use any unsuitable cleaning agents, chemicals or techniques for cleaning. [. . . ] Alternative installation for manual columns 1. Connect the external power supply unit (10 450 266) to the Leica LED3000 NVITM. Place the Leica LED3000 NVITM on the objective from below and tighten the locking screw. diameter of 58 mm. with any objectives that have an outer The Leica LED 3000 NVITM can be used between 50 mm and 150 mm. The supported working distance is Leica Z6 APO / Z16 APO User Manual 46 Quick Start Guide Leica Z6 APO / Z16 APO User Manual 47 Overview of a Manual Leica Z Series Macroscope (Leica Z16 APO) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Digital camera ErgoTubeTM Eyepieces Adjustable eyepiece tubes Video/Phototube Y Microscope carrier Iris diaphragm Optics carrier (zoom body) Click stops on/off Zoom wheel Fine focus Objective LED ring illuminator incident-light Microscope column Focusing drive 1 2 3 4 5 6 7 8 9 10 11 12 13 15 16 14 Leica Z6 APO / Z16 APO User Manual 48 Eyepieces and Focusing Leica Z6 APO / Z16 APO User Manual 49 Magnification Factors of the Eyepieces An eyepiece not only makes it possible to look passively into the macroscope, but also has a critical effect on the maximum magnification. The magnification factor is between 10x and 40x. The following eyepieces are available for the Z series: Magnification 10× 16× 25× 40× Dioptric Correction ± 5 diopter settings ± 5 diopter settings ± 5 diopter settings ± 5 diopter settings Order number 10 450 023 10 450 024 10 450 025 10 450 026 Leica Z6 APO / Z16 APO User Manual 50 Using the Eyepieces The eyepieces form the connection between the tube and the eye of the observer. Simply push them into the tube and they are ready to use. Each eyepiece offers a certain magnification factor that has a determinative effect on the total magnification. Furthermore, all Leica eyepieces can be equipped with practical graticules that enable measuring and quantifying of specimens. Dioptric Correction A built-in dioptric correction is available for eyeglass wearers. Hold the eyepiece firmly and rotate the eyecups forwards counterclockwise. Hold the eyepiece firmly and rotate the eyecups clockwise towards the rear, as otherwise the viewing distance is too great. 2. If an eyepiece is equipped with the integrated dioptric correction, turn the value to the "0" mark. 2. If an eyepiece is equipped with the integrated dioptric correction, turn the value to the "0" mark. By the way, one benefit of viewing with eyeglasses is a drastically lower risk of bacterial transmission (see page 55). The soft material of the eyecup also ensures that your glasses will not be scratched, even if they contact the eyepiece. Leica Z6 APO / Z16 APO User Manual 51 The Correct Interpupillary Distance The interpupillary distance is correctly set if you see a single circular image field when looking at a specimen. If you are still a novice macroscope user, you may need a short time to become accustomed to this. Not to worry--after a little while, it will become automatic. Reference value The distance between eye and eyepiece measures approx. 22 mm for 10/23B wide-field eyepieces for persons wearing glasses. Adjusting the interpupillary distance 1. Push the eyepieces together or separate them until you see a circular image. Slowly approach the eyepieces with your eyes until you can see the complete image field without corner cutting. Leica Z6 APO / Z16 APO User Manual 52 Dioptric Correction Leica macroscopes are parfocally matched. [. . . ] aperture Yes*** Yes*** Remote control options Yes**** Yes AntiShockTM Pads Yes Yes Dimensions of base (W×H×D) 340×390×95 mm 340×440×95 mm *Single-sided **With cold light source Leica CLS150 LS ***Concave mirror ****With external light source Leica Z6 APO / Z16 APO User Manual 113 Leica IsoProTM Motorized XY Stage Compatibility Stage size (L × W × H) Travel Speed X, Y Motor resolution X, Y Repeatability X, Y Positioning accuracy X, Y Hysteresis X, Y Motor Backlash Adapter Acceleration Computer connection Control options Power supply Leica incident-light and TL bases (TL BFDF, TL RCTM, TL RCITM) 335. 5 mm × 370 mm × 41. 5 mm 152 mm × 102 mm (6" × 4") 30 mm/s 0. 25 µm ± 2 µm ±20 µm over the entire positioning range 30 µm Direct current (DC) motor with encoder Slack-free All adapters for TL bases S-shaped acceleration USB Leica PSCTM, Leica Smart Move, Leica LAS via PC Input: 100­240 VAC 50 / 60 Hz 1. 0 A Output: 15 VDC 2. 66 A 40W max. Leica Z6 APO / Z16 APO User Manual 114 Appendix Leica Z6 APO / Z16 APO User Manual 115 Calculating the Total Magnification and Field of View Diameter Parameter MO ME z q r NFOV Magnification of the objective Magnification of the eyepiece Magnification of the changer position Tube factor, e. g. 1. 5× for coaxial incident light, 1. 6× for 45° ErgoTubeTM Factor of 1. 25× when using video/phototube Y Field number of the eyepiece. Field numbers are printed on the eyepieces: 10× = 21, 16× = 14, 25× = 9. 5, 40× = 6. Example MO ME z q r 1× objective 25×/9. 5 eyepiece Zoom position 4 Coaxial incident light 1. 5×, tube factor Factor 1. 25× Calculation example: Magnification in the binocular tube: MTOT VIS = MO × ME × z × q × r or 1 × 25 × 4 × 1. 5 × 1. 25 = 187. 5× Calculation example: Field of view diameter in the specimen OF: NFOV MO × z ×q ×r Leica Z6 APO / Z16 APO User Manual 116 Care, Maintenance, Contact Persons We hope you enjoy using your high-performance macroscope. [. . . ]