User manual LENCO CR-334

[. . . ] CR-334 Instruction Manual Dual Alarm AM/FM Clock Radio with Triple Display Touchless Snooze and Display Control and SmartSet Function For information and support, www. lenco. eu 1 TO PREVENT FIRE OR SHOCK HAZARD, DO NOT USE THIS PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. IMPORTANT SAFETY INSTRUCTIONS 1. ) 2. ) 3. ) 4. ) 5. ) 6. ) Read these instructions. Install in accordance with the manufacturer's instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. [. . . ] But if you continue holding the SET < or > buttons the display will change rapidly. NOTE: If you manually adjust the time, your new setting is entered into the automatic time setting system memory. If the power is interrupted, the display will return to your new setting, not the original setting, when the power is restored. Adjusting The Wake Up Times Your automatic time setting clock radio has two separate alarms that can be set and used independently. You may use the alarms to wake two people at different times, or you may use one alarm for weekdays and the other for weekend wake up times. The procedure for adjusting the wake up time is the same for both Alarm 1 and Alarm 2. 1. ) Press and hold either the ALARM 1 or ALARM 2 setting button. 2. ) Set the VOLUME control to a low setting. 3. ) Press the RADIO ON/OFF button to turn the radio `On'. 4. ) Select your desired station with the TUNING control. 5. ) Adjust the VOLUME control to the desired setting. 6. ) When you are finished listening, press the RADIO ON/OFF button to turn the radio `Off'. The radio dial pointer light goes off. Antenna Information AM ­ The AM bar antenna is inside the cabinet. If AM reception is weak, change the position of cabinet until the internal antenna picks up the strongest signal. FM ­ The FM antenna is located at the back of the unit. If FM reception is weak, extend the FM antenna to its full length or try varying the position and direction of the FM antenna until you find the strongest signal. 7 Wake To RADIO 1. ) Turn the radio `On' by pressing the RADIO ON/OFF button and select the Band, Station, and volume level that you wish to hear when the alarm comes on, then turn the radio `Off' again. 2. ) Reconfirm the wake up time and alarm mode settings for the alarm you are using, Alarm 1, Alarm 2, or both Alarms. 3. ) Set the ALARM selector switch for one or both alarms to the "RADIO" position. The appropriate ALARM 1 and/or ALARM 2 displays will change from "OFF" to the selected wake up time. 4. ) At the selected wake up time the radio will turn `On'. It will play for one hour and then shut off automatically. 5. ) To stop the radio sooner, press either the appropriate ALARM 1 or ALARM 2 button, or press the RADIO ON/OFF button. The radio will stop but the alarm remains set and will turn the radio on again at the same time on the following day (depending on the Alarm Mode setting). 6. ) If you do not want the alarm to turn the radio on the following day, set the appropriate ALARM selector to the "OFF" position. [. . . ] You'll have to do this again five to eight years from now! Resetting The Clock After A Total Memory Loss 11 If you do not change the built-in lithium battery within a reasonable period of time after you see the warning indicator, the lithium battery may become exhausted and will no longer be able to supply back up power to the automatic time setting system internal computer. If the unit is disconnected from the AC outlet after the battery is exhausted, or if a power interruption occurs, the automatic time setting memory will be lost and the clock will need to be reset when the power is restored. Be sure to install a fresh lithium battery before you reset the clock; otherwise the clock will need to be reset each time the power is interrupted. If the lithium battery is exhausted and you experience an interruption in the AC power supply, the clock will reset itself to its initial default setting when the power is restored. [. . . ]