User manual LENCO DVD-51

[. . . ] DVD-51 SAFETY INFORMATION SPECIFICATIONS Card Reader Video Format The light flash with an arrowhead symbol, within an equilateral triang , is intend to alert the user to the le presence of uninsulated "dangerous voltage " within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within the equilatera triangle is intended to alert the user to the presence of important l operating and maintenance (servicing) instructions in the literature accompa nying the appliance. This digital video disc player employs a laser System . Use of controls , adjustment or the performance of procedures other than specifid may result here in hazardous radiation e exposure . [. . . ] Y may use the counterparts on the remote controller to do the same. Note: DV D EXIT SETUP e) SPEAKER SETUP The speaker setup options are illustrated below: A. Do not place this equipment in a place exposed to direct sunlight or strong light source like inverting fluorescent light, or else it may interfere with correct operation of the remote controller. when other similar remote controller is used in the same room, or when this product is used near other equipment using infrared ray, interference with the operation of this remote controller may occur. do not place any object on the remote controller or else it may cause unintentional depression of the buttons and waste the batteries unnecessarily. The front of the chassis should not be glazed with color glass, or else it may cause interference with normal operation of the remote controller. Any barrier between the remote controller and remote sensor will inactivate any operation of the remote controller. The operating range between the remote controller and the equipment shall be no more than 5 meters (16 feet). When the operating range becomes shorter, replace the batteries with new ones. Highlight the AUDIO OUT option, and press the Arrow buttons to choose the audio output mode you prefer. Press Enter to confirm; There are 3optional audio output modes: ANALOG, SPDIF/ RAW, and SPDIF/ PCM. ANALOG: From the Coaxial Output jack and the Optical Output jack, no signal is output. SPDIF/ RAW: Choose this setting if your DVD player is connected to a power amplifier with a coaxial cable or an optical cable; When playing a disc recorded with Dolby Digital, DTS and MPEG audio formats, the corresponding digital signals will be output from the Coaxial Output jack or Optical Output jack. This player's digital output jacks are designed for a 16 DOWN MIX Use the Up and Down arrow button to move the scroll and adjust the saturation. LT / RT: Choose this setting, it will be sound like in a movie theatre if the original movie the disc was recorded from was encoded in the Pro Logic Dolby Digital format. STEREO: Choose this setting, when 5. 1-channel sound playing, two channels of signals will be output 5 SYSTEM CONNECTION 1. System connection DO NOT Connect the AC power socket to the wall outlet before the system connection is completed. SETUP MENU SYSTEM TV TYPE 16 : 9 (Wide Screen): Choose this setting if your DVD player is connected to a wide screen TV If you . choose this setting and you don't have a wide screen TV the images , on the screen may appear distorted due to vertical compression. 4 : 3 LB (Letter Box): Choosing this setting if your DVD player is . connected to a normal ratio TV connector You'll see the movies in their original aspect ratio (height-towidth ratio). You'll see the entire frame of the movie, but it will take up a smaller portion of the screen vertically. The movie might appear with black bars at the top and bottom of the screen. 4 : 3 PS (Pan & Scan): Choosing this setting if your DVD player is . [. . . ] With each consecutive press of the P /N button, the TV system switches. NOTES: If AUTO TV system selected, it can auto reach the highest definition depends on the disc. If it isn't full screen state (note: Wide Screen program would never reach full screen state) or in black and white, press the P / N button to adapt TV System to the TV set of NTSC or PAL. Mute the Audio Output (compatible with DVD, SVCD, VCD, CDHD-CD, MP3 , discs) Pressing the Mute button allows you to reduce sound to an inaudible level, and "MUTE" will be displayed on screen. [. . . ]