User manual LENOXX HT391

[. . . ] MODEL HT-391 Home Theater System Turns Your DVD Player Into a 5. 1 Channel Home Theater Surround Sound System The Perfect Sound System for Your DVD Player · Incredible surround sound, perfect for DVD viewing & enhanced TV game experience. · Also provides superior sound for computer system PLEASE READ CAREFULLY BEFORE USE IB-HT391-WM-E-073003 · Just add your TV & DVD player; everything else is in the box. SAFETY INSTRUCTIONS WARNING TO PREVENT FIRE OR SHOCK HAZARD, DO NOT USE THE PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. AC ~ 120V 60Hz POWER CONSUMPTION: 100 Watts MADE IN CHINA SEE BOTTOM OF THE MAIN SET. WARNING RISK OF EL ECTRIC SHOCK FCC NOTE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. [. . . ] NOTE: You may insert the video cable directly into the VIDEO OUT jack on the back of your DVD and into the VIDEO IN jack on the back of your HOME THEATER SYSTEM. Then insert the video cable into the VIDEO IN jack on your TV, and into the VIDEO OUT jack on the back of your HOME THEATER SYSTEM. Insert the AC power cord into an AC outlet. Make sure the POWER switch on the back of the main unit is at "ON" position. Next press the ON/STANDBY button on the front of the main set or on the REMOTE to turn the set on (or off). NOTE: The factory's default input source is DVD with 5. 1 channel sound output. When the set is turned to ON, the DVD indicator and 5. 1 channel indicator will be on and sound will come out of 5 speakers plus the subwoofer. To change 5. 1 channel to 2 channel output, press the SPEAKER CHANNELS button. The sound will come out of only 2 front speakers plus the subwoofer. Make sure your DVD player is on and follow your DVD player's instructions. NOTE: For some DVDs, if the sound output is not set to analog, the audio cables may not be active and there will be no sound output. If this happens, check and make sure your DVD's sound output is set to analog. Go to Page 21 for other detailed instructions. NOTE: Your cable or antenna connection to your TV are not affected with this connection. Leave your antenna cable connected to your TV as you normally would. No changes will be made to your current antenna connections. 13 IB-HT391-WM-E-073003 TV + VCR CONNECTIONS Home Theater System + TV + VCR CABLE OR ON AIR ANTENNA/ SATELLITE SIGNAL This does not change from your current connection. CONNECT ALL SPEAKERS AS SHOWN ON PAGE 8 (OR THE QUICK SETUP DIAGRAM SHEET) 1. Insert the stereo audio cables (included) into the AUX INPUT L (left=white) and R (right=red) jacks or any available set of input jacks on the back of your HOME THEATER SYSTEM, and into the corresponding AUDIO OUT jacks on your VCR, this will allow your VCR's sound to play through your HOME THEATER SYSTEM. Connections of your cables are not changed when you add your HOME THEATER SYSTEM. NOTE: You will hear sound from both the TV and your HOME THEATER SYSTEM, this is normal. 2. 3. 4. Insert the AC power cord into an AC outlet. Make sure the POWER switch on the back of the main unit is at "ON" position. Next press the ON/STANDBY button on the front of the main set or on the REMOTE to turn the set on (or off). NOTE: The factory's default input source is DVD with 5. 1 channel sound output. [. . . ] If the batteries are weak or dead, replace them with new ones (size "AAA"). Point the remote control unit at a distance of less than 20 feet from the main unit of the HOME THEATER system. Remove any obstacles between the remote control unit and remote control sensor. If the battery terminals are dirty or corroded, clean them with sandpaper. [. . . ]