User manual LENOXX PH329

[. . . ] ® 13 MEMORY SPEAKERPHONE WITH ELECTRONIC HOLD MODEL: PH-329 OPERATING INSTRUCTIONS SPEAKERPHONE WITH INDICATOR 13 MEMORY TELEPHONE TONE/PULSE SWITCHABLE DIALING RECEIVER VOLUME CONTROL FLASH & REDIAL BUTTON DESK OR WALL MOUNTABLE HOLD BUTTON WITH INDICATOR (3 ONE TOUCH & 10 TWO TOUCH) NOTE: READ AND FOLLOW THESE INSTRUCTIONS BEFORE USING YOUR TELEPHONE PH-329100699 MS V. 2 E IMPORTANT SAFETY INSTRUCTIONS When using your telephone equipment, the following basic safety precautions should always be followed to reduce the risk of fire, electric shock and personal injury: 1. Read and follow all instructions and warnings. Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. [. . . ] You should also save the packing material if you want to move or ship this phone. This product is an electrical device and can be hazardous if immersed in water. To avoid the possibility of electrical shock, do not use it while in the bathtub or shower or when you are wet. If you accidentally drop it into water, first unplug its cord from the modular jack, then remove the equipment from the water. Avoid using this telephone during electrical storms in your immediate area, even though your telephone company may be using protective measures to limit electrical surges from entering your home, absolute protection from lightning is impossible. PH-329100699 MS V. 2 E 4 INSTALLATION INSTRUCTIONS INSTALLATION TELEPHONE BASE HANDSET STRAIGHT TELEPHONE CORD To Telephone Jack COILED HANDSET CORD 1. Insert the modular plugs of the Coiled Handset Cord into the jack of the Telephone Handset and into the jack on the SIDE of the Telephone Base. Insert the modular plugs of the Straight (not coiled) cord into the modular jack at the REAR of the Telephone Base and into the Telephone Wall Jack (either end can be plugged in). This set is designed to connect directly to a modular jack MODULAR JACK If you have a 4-prong style jack, simply use a modular adaptor (not included). TELEPHONE LINE (4-prong style jack) RINGER ON/OFF SWITCH This switch is located on the rear of the set. Select the desired function of the ringer. O N - Normal setting, rings on incoming calls. O F F - The ringer does not sound, for undisturbed privacy. NOTE: If your Ringer Switch is in OFF position, only THIS phone will not ring, other phones in your home on the same line will ring. TONE/PULSE SWITCH Select the type of dialing that you desire or that your telephone system requires. TONE - The phone will operate using tone dialing. (If your phone doesnt dial out, switch to PULSE. ) PULSE - The phone will dial using rotary pulse dialing . NOTE: Even when your phone is set to pulse service, this phone can be switched to temporary tone dialing for access to services that require tone signaling like computer systems. Just press the button after dialing in pulse and your buttons can now be used for tone signaling for this call only. NOTE: When installation is completed, pick up the Handset to listen for dial tone before using speakerphone for the first time. 5 PH-329100699 MS V. 2 E TELEPHONE OPERATION RECEIVING CALLS AS A NORMAL TELEPHONE When your telephone rings 1. Lift the Handset and speak into the mouth piece of the Handset. Hang up the Handset to release the telephone line when conversation is completed. Select the desired dialing mode with the Tone/Pulse Switch (do this only the first time after installation). Pick up the Handset and listen for dial tone. [. . . ] Do not allow any liquids to get inside the case. TROUBLE SHOOTING PROBLEM No dial tone Phone is dead Can make calls but phone does not ring Can receive but cannot make calls LIKELY CAUSES 1. If your other telephones are Rotary type phones, your line may be conditioned to accept Pulse dialing only. Move Tone/Pulse Switch to Pulse position. C o n t a c t y o u r p h o n e c o m p a n y t o h a v e y o u r l i n e c h a n g e d t o To n e a n d P u l s e service. Static noise on line or cannot hear Replace the coil cord. [. . . ]