User manual LENOXX SL326

[. . . ] Heat - The appliance should be situated away from heat sources such as radiators, heat registers, stoves, or other appliances (including amplifiers) that produce heat. Power Sources - The appliance should be connected to a power supply only of the type described in the operating instructions or as marked on the appliance. Grounding or Polarization - Precautions should be taken so that the grounding or polarization means of an appliance is not defeated. Power Cord Protection - Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenient receptacles, and the point where they exit from the appliance. [. . . ] This is normal for this type of player. Go to the next track Go back to the previous track Locate a point in a song FORWARDS BACKWARDS or Press and hold down while playing until you find the point. Press the CD DOOR OPEN button (press STOP first) Press the POWER switch, the AC POWER STANDBY INDICATOR will go on. Remove the CD Turn off the player 5 SL-326SY041200L v. 1 E REPEAT PLAY PLAYING CD SONGS (TRACKS) OVER AND OVER You can play CD tracks over and over in normal or programmed play modes (see page 7). PROGRAM CD FUNCTION SWITCH GRAPHIC EQUALIZER POWER SWITCH 1. 4. Press the POWER switch, the AC POWER STANDBY INDICATOR will go off. Select the track by pressing or , and then press . Press the CD REPEAT button. To repeat a single track (song) Press Press the REPEAT button twice Display shows REPEAT Flashing REPEAT steady on all the tracks (all songs) Press the REPEAT button once programmed tracks During programmed play, press REPEAT steady on (MEMORY also the REPEAT button once on) To cancel Repeat Play Press the REPEAT button until the REPEAT goes off in the display. 6 SL-326SY041200L v. 1 E SELECTING YOUR OWN MUSIC PLAYING ORDER (Programmed Play) You can make a program of up to 20 tracks in the order you want them to be played. PROGRAM NOTE: Programming is only done during stop mode. 1 2 3 4 5 PLAY/PAUSE SKI P/SEARCH During STOP mode, press the PROGRAM (MEMORY) button. The display will show , MEMORY and TRACK will flash in the display. Press the SKIP/SEARCH buttons either or until the desired track shows in the display. MEMORY TRACK MEMORY TRACK DOWN - TUNING - UP Press the PROGRAM button. The display will show . MEMORY TRACK Repeat steps 2&3 until all the desired tracks are programmed. Press the PLAY button to start program play. MEMOR Y and TRACK will be steady in the display, the track number being played will show in the display. MEMORY TRACK To change the current program To cancel Program Play Press the STOP button. Just create a new program following the programing procedure. 7 SL-326SY041200L v. 1 E LISTENING TO THE RADIO 3 2 6 1 4 Press the POWER switch, the AC POWER STANDBY INDICATOR will be off. Press the RADIO FUNCTION switch. CD Connect the AC power cord (see page 3). 1 2 3 4 RADIO POWER FUNCTION TAP E Press the BAND switch to choose the proper band (AM or FM ) that you want. DOWN - TUN IN G - U P Tune into the station you prefer using the TUNING UP or DOWN button. Each time the button is pressed, the frequency changes. Keep the button pressed, the station will change rapidly (automatic tuning), release the button and it will stop at the next strong station. (NOTE: For FM stations, unwind and straighten out the FM antenna at the back of the set. ) STEREO will light up when receiving FM Stereo broadcasts. 5 FM STEREO MHZ 6 Press the GRAPHIC EQULALIZER button to choose different music effects (CLASSIC, ROCK, POP or normal). 8 SL-326SY041200L v. 1 E Allows you to store your favorite stations for quick one button tuning. PRESETTING RADIO STATIONS 2&4 3 Connect the AC power cord (see page 3). 1 2 3 4 REPEAT Follow Steps 1 to 4 (LISTENING TO THE RADIO on the previous page) to select a station. Press the PROGRAM (MEMORY) button, CH will show and MEMORY will flash in the display for about 5 seconds. While the MEMORY is flashing, press the PRESET (REPEAT) button to choose a memory location (01-20). Press the PROGRAM (MEMORY) button again to confirm, the station now broadcasting is stored into that preset memory location. MEMORY disappears from the display. MEMORY CH FM MHZ MEMORY CH PRESET FM MHZ CH FM MHZ NOTE: Steps 2-4 should be done quickly. 5 Repeat the above steps to store other 19 stations into memory. TIP: UP TO 20 AM AND 20 FM STATIONS CAN BE STORED INTO THE PRESET MEMORY LOCATIONS. 9 SL-326SY041200L v. 1 E LISTENING TO THE PRESET STATIONS (after you programmed them) 1 2 3 POWER Press the POWER switch, the dial will light. Press the AM/FM BAND switch to select the desired band. Connect the AC power cord (see page 3). 2 REPEAT PRESET Press the PRESET (REPEAT) button several times to choose a memory location (01-20). You will receive the station you stored into that preset memory location. 1 3 USE THESE OPERATIONS 3 2 BUTTONS FOR ADDITIONAL To 1. Adjust the volume Press or Adjust VOLUME control POWER switch EQUALIZER button 1 2 . [. . . ] Make sure the TAPE FUNCTION switch is pressed. Tape player The tape does not erase completely. The tape does not record. Clean the erasing head (see page 17). Make sure the tape is inserted properly. the safety tab of the cassette Clean the heads, pinch roller and capstan (see page 17). [. . . ]