User manual LEXICON I-ONIX U82S

[. . . ] Owner's Manual IMPORTANT SAFETY INSTRUCTIONS WARNING FOR YOUR PROTECTION READ THE FOLLOWING: KEEP THESE INSTRUCTIONS HEED ALL WARNINGS FOLLOW ALL INSTRUCTIONS THE APPARATUS SHALL NOT bE ExPOSED TO DRIPPING OR SPLASHING LIqUID AND NO ObjECT FILLED WITHI LIqUID, SUCH AS vASES, SHALL bE PLACED ON THE APPARATUS. DO NOT bLOCK ANY OF THE vENTILATION OPENINGS. INSTALL IN ACCORDANCE WITH THE MANUFACTURER'S INSTRUCTIONS. DO NOT INSTALL NEAR ANY HEAT SOURCES SUCH AS RADIATORS, HEAT REGISTERS, STOvES, OR OTHER APPARATUS (INCLUDING AMPLIFIERS) THAT PRODUCE HEAT. [. . . ] MIc/LIne GaIn KnOB Adjusts the input gain level for the indicated Mic/Line input. 11. StereO ButtOn anD StereO LeD This button toggles between Stereo mode and Mono mode for the Mic/Line inputs on either side of it. In Stereo mode (Stereo LED is on), the left input signal (Mic/Line 3, for example) is sent to the Left Main Out, while the right input signal (Mic/ Line 4, for example) is sent to the Right Main Out. In Mono mode (Stereo LED is off ), each pair of input signals is mixed together and sent to the Left and Right Main Outs as a mono signal. 12. 48v LeD Lights when phantom power is active for the inputs on either side of the LED. Phantom power can be turned on for each combi-jack input pair via the 48V buttons on the back panel. Dynamic microphones do not require phantom power to operate, but are not harmed by it. Most condenser microphones do require phantom power to operate. If you are unsure about the phantom power requirements for your microphone, consult your microphone's documentation or contact the manufacturer. 13. OutPut LeveL KnOB 4 Controls the Left and Right Main output level. 14. S/PDIf LeD Lights when a S/PDIF connection is detected. Note that S/PDIF communication is disabled unless a USB connection is established. 15. MOnItOr MIX KnOB The I·ONIX U82S unit gives you the ability to hear your analog input signals directly and immediately while recording without having to adjust levels in software and before the delay caused by digital converters and computer recording latency. This zero-latency analog monitoring is controlled by the Monitor Mix knob, which you can use to adjust the blend between the live analog inputs (called "Direct") and any sounds coming back from the computer via USB ("Playback"). To hear only the live source input signals plugged into the U82S, turn the Mix knob fully left to Direct. To hear only the mix from the computer, turn the Mix knob fully right to Playback. Any signal coming in on the S/PDIF input is converted to analog and sent to the mix control so that you can monitor this input directly (via playback only) just like an analog input. The output from the Monitor Mix control is routed to the Main outputs and Headphone outputs. 16. uSB LeD Lights when a USB connection is detected. 5 rear and Side Panels 123 4 5 6 78 1. InStruMent 1 anD InStruMent 2 InPutS 9 These unbalanced inputs accept 1/4" connectors and support instrument level sources (including guitars). Note that when the Instrument 1 input is connected, the Mic/Line input 1 is disabled. The same is true for the Instrument 2 and Mic/Line 2 inputs: when the Instrument is connected, the Mic/Line is disabled. 2. [. . . ] Once the locaters are set, go to File > Export > Audio mixdown. Click on the Choose button and name the file in the File name: field and select the location that you want the . wav file to be saved to in the Look in field and click the Save button. The file must first be saved onto your computer's hard drive before it can be burned onto a CD. Next, select Wave File (. wav) in the `File Format' field, set Sample Rate to 44. 1 kHz, set Bit Depth to 16 bit, and click Export. Options and Features in Cubase LE 4 Cubase LE 4 contains many advanced features and options for recording, editing and mixing audio. [. . . ]