User manual LEXICON MC-12 V1.1 RELEASE NOTES REV 1

[. . . ] MC-12 Software Version 1. 1 Release & Errata Notes DOCUMENTATION CONVENTIONS This document is a supplement to the MC-12 User Guide (Rev 1). It contains release notes that provide information about the new and enhanced features of Software Version 1. 1. It also includes errata notes for the MC-12 User Guide (Rev 1). Refer to the user guide for general safety, installation, and operating instructions. [. . . ] STATUS menus can still be accessed with the remote control. Press the SHIFT button, then the STAT button to access the first page of the STATUS menu for the active listening mode. Press the STAT button a second time to access the second page of the menu. Press the STAT button a third time to exit the menu. (If the STATUS menu does not include a second page, pressing the STAT button a second time will exit the menu. ) The 5. 1 BYPASS listening mode is now called the 5. 1a BYPASS listening mode. Likewise, the 5. 1 BYPASS STATUS menu is now called the 5. 1a BYPASS STATUS menu. Level meters are no longer available on the 5. 1a BYPASS STATUS and 2CH BYPASS STATUS menus. An alphabetical glossary of listening mode parameters begins in the next column and on page 5-20 of the MC-12 User Guide in the next column. An alphabetical glossary of all listening mode parameters begins on page 5-20 of the MC-12 User Guide (Rev 1). The 2. 0 ENCODING parameter has been added to the DOLBY D STATUS menu. When the parameter value is MATRIX, matrix-encoding is present in the input signal. When the parameter value is NONE, no matrix-encoding is present in the input signal. BIT RATE (32 to 3072kbps) The BIT RATE parameter has been added to the DOLBY D and dts(-ES) STATUS menus. It indicates the rate at which the input signal is encoded. A higher bit rate indicates that less compression was used during the encoding process. CENTER MIX LVL (-3. 0dB, -4. 5dB, -6. 0dB) The CENTER MIX LVL parameter has been added to the DOLBY D STATUS menu. It indicates the relative level of the center channel that was used during the mixing process. DIALOG OFFSET (-31 to 0dB) Note: Remote control MENU arrows can be used to scroll listening mode STATUS menu parameters when the MAIN command bank is active. STATUS menu parameters are not adjustable. The DIALOG OFFSET parameter has been added to the DOLBY D STATUS menu. It indicates the dialog normalization value applied to the input signal. Dolby Digital input sources reproduce dialog at 31 decibels below full-scale (-31dBFS). When the dialog normalization value of the incoming signal is higher or lower, the DIALOG OFFSET parameter indicates the amount of adjustment the unit makes to normalize dialog to -31dBFS. . New Listening Mode Parameters continues on page 12 11 Software Version 1. 1 Release & Errata Notes New Listening Mode Parameters (continued from page 11) ES DECODING (AUTO, ON, OFF) MIX ROOM Lexicon (SMALL, LARGE) The ES DECODING parameter has been added to the dts(-ES) L7 FILM, dts(-ES) L7 MUSIC, dts(-ES) THX, dts(-ES), and dts(-ES) 2-CHAN listening mode menus. [. . . ] The Mute button LED lights whenever mute is activated, either automatically or manually. For example, the unit will briefly activate mute when switching input sources or listening modes. When the preferred listening mode selection parameters on the INPUT SETUP menu are set to USE LAST, the unit will revert to the previously-selected listening mode when the current input is deselected, then reselected. However, when the 2-CHANNEL listening mode is selected with the 2CH button on the remote control, the unit will revert to the listening mode that was selected prior to the 2-CHANNEL listening mode. Software Version 1. 1 Release & Errata Notes 15 Software Version 1. 1 Release & Errata Notes REVISED MENU TREE The menu tree that begins below replaces the menu tree that begins on page A-5 of the MC-12 User Guide (Rev 1). MAIN MENU MODE ADJUST AUDIO CONTROLS SETUP SETUP INPUTS SPEAKERS REAR PANEL CONFIG DISPLAYS VOLUME CONTROLS TRIGGERS LOCK OPTIONS AUDIO CONTROLS BASS +0. 0dB TREBLE +0. 0dB TILT EQ +0. 0dB LOUDNESS OFF BALANCE <|> FADER <|> ZONE2 BALANCE <|> RECORD BALANCE <|> Lexicon INPUT SETUP DVD1 DVD2 LD TV SAT VCR CD PVR GAME TAPE TUNER AUX Continued on page 17 SPEAKER SETUP CUSTOM SETUP THX SETUP SPEAKER DISTANCES LEVELS CALIBRATION R 40Hz C 60Hz M SUB 40Hz 40Hz L SL 60Hz RL 60Hz SR 60Hz RR 60Hz REAR PANEL CONFIG 8 STEREO INPUTS OR 5 STEREO & 5. 1 ANLG DISPLAY SETUP ON-SCREEN DISPLAY FRONT PANEL DISPLAY A/V SYNC DELAY OFF CUSTOM NAME OFF EDIT CUSTOM NAME Continued on page 20 Continued on page 19 MODE ADJUST FILM TV MUSIC PL II PRO LOGIC II PL II MUSIC PRO LOGIC FILM MUSIC 2-CH SURROUND 2-CHANNEL MONO LOGIC MONO SURROUND MONO 5. 1 FILM 5. 1 TV 5. 1 MUSIC 5. 1 SurEX DIGITAL 5. 1 2-CHANNEL 5. 1 MONO LOGIC 5. 1 MONO SURR 5. 1 MONO FILM MUSIC R R VOLUME CONTROL SETUP MAIN PWR ON -30dB MUTE LEVEL -30dB ZONE PWR ON -30dB REC PWR ON -30dB TRIGGER SETUP TRIGGER 1 REMOTE TRIGGER 2 REMOTE Continued on page 20 LOCK OPTIONS MODES UNLOCKED AUDIO CNTRL UNLOCKED SETUP UNLOCKED Continued on page 21 2-CHAN 5. 1a FILM 5. 1a MUSIC 5. 1a SurEX 5. 1a STANDARD 5. 1a 2-CHANNEL 5. 1a BYPASS 2CH BYPASS 16 MC-12/MC-12 Balanced Software Version 1. 1 Release & Errata Notes Continued from page 16 The menu pictured at the left prompts the selection of the desired input for configuration. [. . . ]