User manual LEXICON MC-8

[. . . ] MC-8 Digital Controller User Guide IMPORTANT SAFETY INSTRUCTIONS 1. Install in accordance with the manufacturer's instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not defeat the safety purpose of the polarized or grounding-type plug. [. . . ] Whenever it appears, any other INPUT SETUP menu may be substituted. Likewise, whenever the DVD1 input appears as a step in a menu path, any other input may be substituted. S-VIDEO 16:9 SETUP INPUTS DVD1 MAIN ADVANCED S-VIDEO 16:9 AUTO, OFF Controls the passage of anamorphic trigger signals present in some video sources. When set to AUTO, the MC-8 allows anamorphic video input signals to pass through the S-video switcher, enabling compatible display devices to automatically switch between anamorphic and non-anamorphic display modes. When set to OFF, the MC-8 prevents anamorphic video input signals from passing through the S-video switcher, preventing compatible display devices from automatically switching between anamorphic and non-anamorphic display modes. . MAIN ADVANCED continues on page 3-22 3-21 SETUP MAIN ADVANCED MAIN MENU MODE ADJUST AUDIO CONTROLS SETUP Lexicon (continued from page 3-21) SETUP INPUTS SPEAKERS REAR PANEL CONFIG DISPLAYS VOLUME CONTROLS TRIGGER LOCK OPTIONS INPUT SETUP DVD1 DVD2 SAT VCR TV CD TUNER AUX DVD1 INPUT SETUP NAME DVD1 DIGITAL IN COAX-1 ANALOG IN NONE ANLG IN LVL AUTO VIDEO IN S-VIDEO-1 COMPONENT IN 1 2-CH L7 FILM %!D 5. 1 L7 FILM DTS-ES DTS-ES L7 FILM MAIN ADVANCED ZONE2 IN DIGITAL DVD1 MAIN ADV INPUT SELECT DIGITAL 2-CH ANLG BYP OFF S-VIDEO 16:9 AUTO S-VIDEO OSD 4:3 ON COMPONENT OSD OFF ON OFF The DVD1 INPUT SETUP menu is shown here as an example, and will continue to be shown as an example throughout this section. Whenever it appears, any other INPUT SETUP menu may be substituted. Likewise, whenever the DVD1 input appears as a step in a menu path, any other input may be substituted. S-VIDEO OSD 4:3 SETUP INPUTS DVD1 MAIN ADVANCED S-VIDEO OSD 4:3 ON, OFF Note: The on-screen display appears horizontally stretched across the display device screen when all of the following conditions are met: · · · The S-VIDEO OSD (4:3) parameter is set to OFF. An anamorphic video input signal is present. A 16:9 display device (widescreen) is connected to an S-video output connector. Controls the appearance of the on-screen display when the display device is connected to an S-video output connector. When set to ON, the display device shows the on-screen display in a 4:3 aspect ratio* regardless of the incoming signal. When set to OFF, the display device shows the on-screen display in the same aspect ratio as the input signal. * Aspect ratio refers to the size of the picture on the display device screen or to the size of the display device screen. A 16:9 aspect ratio, often referred to as "widescreen, " is almost twice as wide as high. 3-22 MC-8 SETUP MAIN MENU MODE ADJUST AUDIO CONTROLS SETUP SETUP INPUTS SPEAKERS REAR PANEL CONFIG DISPLAYS VOLUME CONTROLS TRIGGER LOCK OPTIONS INPUT SETUP DVD1 DVD2 SAT VCR TV CD TUNER AUX DVD1 INPUT SETUP NAME DVD1 DIGITAL IN COAX-1 ANALOG IN NONE ANLG IN LVL AUTO VIDEO IN S-VIDEO-1 COMPONENT IN 1 2-CH L7 FILM %!D 5. 1 L7 FILM DTS-ES DTS-ES L7 FILM MAIN ADVANCED ZONE2 IN DIGITAL DVD1 MAIN ADV INPUT SELECT DIGITAL 2-CH ANLG BYP OFF S-VIDEO 16:9 AUTO S-VIDEO OSD 4:3 ON COMPONENT OSD OFF ON OFF The DVD1 INPUT SETUP menu is shown here as an example, and will continue to be shown as an example throughout this section. Whenever it appears, any other INPUT SETUP menu may be substituted. Likewise, whenever the DVD1 input appears as a step in a menu path, any other input may be substituted. COMPONENT OSD SETUP INPUTS DVD1 MAIN ADVANCED COMPONENT OSD ON, OFF Controls the appearance of the on-screen display when the display device is connected to the component video output connector. When set to ON, the display device shows the on-screen display as a 480i video signal on a full blue-screen background. To minimize viewing distractions, the two-line status does not appear on the on-screen display. When set to OFF, the display device does not show the on-screen display, including the two-line status (2-18). Note: When the ON-SCREEN DISPLAY menu BACKGROUND parameter (3-51) is set to OFF, the display device using the component video output connector will not show the on-screen display. 3-23 SETUP ZONE2 IN SETUP INPUTS DVD1 ZONE2 IN Lexicon DIGITAL, ANLG, DMIX Controls the interaction of the digital and analog audio input connectors assigned to the selected Zone 2 input. The INPUT SETUP menu can be used to assign one digital and one analog audio input connector for the selected input. Refer to pages 3-7 and 3-8 for more information. The table shown on the next page describes ZONE2 IN parameter settings. MAIN MENU MODE ADJUST AUDIO CONTROLS SETUP SETUP INPUTS SPEAKERS REAR PANEL CONFIG DISPLAYS VOLUME CONTROLS TRIGGER LOCK OPTIONS INPUT SETUP DVD1 DVD2 SAT VCR TV CD TUNER AUX DVD1 INPUT SETUP NAME DVD1 DIGITAL IN COAX-1 ANALOG IN NONE ANLG IN LVL AUTO VIDEO IN S-VIDEO-1 COMPONENT IN 1 2-CH L7 FILM %!D 5. 1 L7 FILM DTS-ES DTS-ES L7 FILM MAIN ADVANCED ZONE2 IN DIGITAL DIGITAL ANLG DMIX The DVD1 INPUT SETUP menu is shown here as an example, and will continue to be shown as an example throughout this section. Whenever it appears, any other INPUT SETUP menu may be substituted. Likewise, whenever the DVD1 input appears as a step in a menu path, any other input may be substituted. CAUTION When the ZONE2 IN parameter is set to DIGITAL or ANLG, the MC-8 recognizes some dts-encoded input sources as audio signals (not data signals) and outputs loud digital noise from the Zone 2 audio output connectors. 3-24 MC-8 SETUP ZONE2 IN Parameter Settings The table below describes ZONE2 IN parameter settings. DIGITAL The MC-8 automatically sets the ZONE2 IN parameter to DIGITAL when the ANALOG IN parameter is set to NONE. [. . . ] Claims for shipping damages must be made with the carrier. Damage to a unit that has been altered, or on which the serial number has been defaced, modified, or removed. Include a copy of the original dated sales receipt. (A copy of the original dated sales receipt must be presented whenever warranty service is required. ) Do not include accessories such as power cords or user guides unless instructed to do so. [. . . ]