User manual LEXICON MV-5

[. . . ] MV-5 Processor User Guide IMPORTANT SAFETY INSTRUCTIONS 1. Install in accordance with the manufacturer's instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not defeat the safety purpose of the polarized or grounding-type plug. [. . . ] Each Mode Family has a subset of available listening modes that can be turned off. If the listening mode is set to OFF, then the applicable listening modes in that family are not available for selection from the mode buttons. If the listening mode is ON, then the applicable listening modes in that family are available for selection. These are not input-specific settings; if a Mode Family option is turned off, it is removed from the list of available listening modes for ALL inputs, and regardless of the incoming data stream. Some modes, such as Dolby Digital, DTS, and the Stereo modes in the PCM menus, cannot be excluded from the mode selections. Note: The Logic 7 Default parameter is the one exception in the Surround Configuration menu - this parameter has different functionality, as described on the following page. MAIN MENU AUDIO CONTROLS VIDEO STATUS SETUP SETUP DISPLAY SETUP SPEAKER/EQ SETUP INPUT SETUP SURROUND CONFIG DOLBY CONFIG MUTE LEVELS POWER ON SETTINGS SURROUND CONFIG LOGIC 7 DEFAULT: ON DOLBY MULTI-CHANNEL DOLBY 2. 0 DTS PCM 44. 1/48 kHz PCM 96kHz DOLBY MULTI-CHANNEL DOLBY 2. 0 DTS DTS 96/24: ON DTS NEO:6: ON DTS-ES MATRIX: ON DTS-ES DISCRETE: ON LOGIC 7: ON STEREO DOWN MIX: ON DOLBY PLII: ON DOLBY PLIIx: ON DOLBY VIRTUAL: OFF LOGIC 7: ON DOLBY VIRTUAL: OFF LOGIC 7: ON STEREO DOWN MIX: ON PCM 44. 1/48 kHz PCM 96kHz LOGIC 7: ON DOLBY PLII: ON DOLBY PLIIx: ON DTS NEO:6: ON 5/7 CH STEREO: ON LOGIC 7: ON DOLBY PLII: ON DOLBY PLIIx: ON DOLBY VIRTUAL: OFF DTS NEO:6: ON HALL: ON 5/7 CH STEREO: ON 3-29 Setup LOGIC 7 DEFAULT SETUP SURROUND CONFIG LOGIC 7 DEFAULT Lexicon OFF, ON Allows the user to choose Logic 7 as the default surround mode for all incoming audio signals. If this parameter is OFF, then the MV-5 selects the native format of the incoming signal as the default listening mode. If set to ON, then all incoming audio signals are defaulted to the Logic 7 listening modes. Setting the Logic 7 Default to ON does not prevent other listening modes from being available through the Mode buttons. Selecting the DOLBY, DTS, DSP, or STER soft button on the remote control switches the Mode menu selections to any listening modes available for those families. Note: The Logic 7 Default is the only menu item in the Surround Config menu that has different functionality. 3-30 MV-5 Setup DOLBY CONFIGURATION Selecting the SETUP menu DOLBY CONFIG option opens the Dolby Configuration menu, which is used to configure the Dolby surround modes for optimum performance. DIMENSION MAIN MENU AUDIO CONTROLS VIDEO STATUS SETUP SETUP DISPLAY SETUP SPEAKER/EQ SETUP INPUT SETUP SURROUND CONFIG DOLBY CONFIG MUTE LEVELS POWER ON SETTINGS DOLBY CONFIGURATION MODE: DOLBY PLII MUSIC CENTER WIDTH:3 DIMENSION: 0 PANORAMA: OFF NIGHT: OFF SETUP DOLBY CONFIG DIMENSION R-1, R-2, R-3, O, F-1, F-2, F-3 Alters the perceived depth of the surround field by creating a shallower presentation (F-1 to F-3) that appears to move the center of the sound field towards the front of the room or a deeper presentation (R-1 to R-3) that appears to move the sound field towards the rear of the room. PANORAMA Note: The Dolby Configuration only applies to the Dolby PLII Music and Dolby PLIIx Music listening modes. The Dolby Pro Logic IIx mode requires a 7. 1-channel configured system. SETUP DOLBY CONFIG PANORAMA OFF, ON MODE SETUP DOLBY CONFIG MODE PLII, PLIIx Appears to increase the sound presentation along the sides of the room by extending the stereo image to include surround channel signals, which enhances the sense of surround sound by creating a "wraparound" effect with side wall imaging. Selects the MODE parameter, which chooses between the Dolby PLII Music and Dolby PLIIx Music listening modes. NIGHT SETUP DOLBY CONFIG NIGHT OFF, MID, MAX CENTER WIDTH SETUP DOLBY CONFIG CENTER WIDTH 0 TO 7 Adjusts the balance of the vocal information in the front soundstage between the center and front left/right speakers. The higher settings spread the center channel sound more broadly into the left and right channels while a lower number produces a tigher center channel presentation. The Center Width range is 0 to 7 in single increments. Adjusts the audio settings for Night mode. The Night mode uses special processing to preserve the dynamic range and full intelligibility of a movie soundtrack while reducing the peak level. This prevents abruptly loud transitions from disturbing others, without reducing the sonic impact of a digital source. Use the MID setting for mild compression and the MAX setting for more severe compression. 3-31 Setup MUTE LEVELS Selecting the SETUP menu MUTE LEVELS option opens the Mute Levels menu, which is used to adjust the mute levels of both the Main Zone and Zone 2 audio outputs. MAIN MENU AUDIO CONTROLS VIDEO STATUS SETUP SETUP DISPLAY SETUP SPEAKER/EQ SETUP INPUT SETUP SURROUND CONFIG DOLBY CONFIG MUTE LEVELS POWER ON SETTINGS MUTE LEVELS MAIN ZONE: -30dB ZONE-2: -30dB Lexicon POWER ON SETTINGS Selecting the SETUP menu POWER ON SETTINGS option opens the Power On Settings menu, which provides user preferences to the Power On Volume and Dock Auto Power settings. MAIN MENU AUDIO CONTROLS VIDEO STATUS SETUP SETUP DISPLAY SETUP SPEAKER/EQ SETUP INPUT SETUP SURROUND CONFIG DOLBY CONFIG MUTE LEVELS POWER ON SETTINGS POWER ON SETTINGS POWER ON VOL: -30dB DOCK AUTO POWER: ON POWER ON VOL MAIN ZONE SETUP MUTE LEVELS MAIN ZONE LAST, -80dB TO -10dB POWER ON VOL FULL, -10, -20, -30, -40dB SETUP POWER ON SETTINGS Allows you to choose different levels of attenuation for Main Zone audio muting. The FULL setting completely mutes the box. The other available settings perform incremental muting. Identifies the starting volume level when the MV-5 is powered on. The Last parameter sets the volume to the same volume that existed when the unit was put into Standby or powered off from the rear panel switch. The Power On Volume can be set from ­80dB to ­10dB in 1dB increments. ZONE 2 SETUP MUTE LEVELS ZONE-2 FULL, -10, -20, -30, -40dB DOCK AUTO POWER SETUP POWER ON SETTINGS DOCK AUTO POWER OFF, ON Allows you to choose different levels of attenuation for Zone 2 audio muting. The FULL setting completely mutes the box. [. . . ] D-2 3-Digit Pre-programmed Codes Worksheet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-6 Appendix D INSTALLATION WORKSHEET INPUT SETUP NAME VIDEO IN V-PROCESS VIDEO OUT HDMI LINK DIG AUDIO ANLG AUDIO DIG/ANLG AUTO MODE FAMILY** MODE** DEFAULT SUR** A/D SAMPLE RATE A/V SYNC DELAY TRIGGER 2 ZONE2 OUT** ADVANCED VIDEO INPUT TYPE SHARPNESS NOISE REDUCTION X-COLOR SUPPRESS DCDi INTERPOL FILM DETECTION FILM EDIT DETECTION FLESHTONE NR D-2 NONE DOCK N/A USB NONE N/A Lexicon HD DVD GAME SAT CABLE DVR CD DOCK PC TUNER AUX1 AUX2 MV-5 Appendix D HD DVD GAME SAT CABLE DVR CD DOCK PC TUNER AUX1 AUX2 INPUT SETUP COMPNT ENHANCE BRIGHTNESS CONTRAST COLOR ADVANCED VIDEO (CONTINUED) SPEAKER SETUP REAR AMP**: ____ CROSS-OVER POINTS** DISTANCES (UNITS: ___)** OUTPUT LEVELS "ALL" INPUT** HD INPUT DVD INPUT GAME INPUT SAT INPUT CABLE INPUT DVR INPUT CD INPUT DOCK INPUT PC INPUT TUNER INPUT AUX 1 INPUT AUX 2 INPUT AUTO SETTING FRONT LEFT ** CENTER FRONT RIGHT SIDE LEFT SIDE RIGHT REAR LEFT REAR RIGHT SUB/ SUB/ LFE LPF LFE HPF SUB 1 SUB 2 D-3 Appendix D SURROUND CONFIGURATION LOGIC 7 DEFAULT** DTS** DTS 96/24 DTS + NEO:6 DTS-ES MATRIX DTS-ES DISCRETE LOGIC 7 STEREO DOWN MIX DOLBY 2. 0** DOLBY PLII DOLBY PLIIx DOLBY VIRTUAL LOGIC 7 DOLBY MULTI-CHANNEL** DOLBY VIRTUAL LOGIC 7 STEREO DOWN MIX PCM 44. 1/48 kHz** LOGIC 7 DOLBY PLII DOLBY PLIIx DOLBY VIRTUAL DTS NEO:6 HALL 5/7 CH STEREO PCM 96 kHz** LOGIC 7 DOLBY PLII DOLBY PLIIx DTS NEO:6 5/7 CH STEREO D-4 Lexicon NO YES AUDIO CONTROLS AUTO EQ** ACTIVE EQ PRESET** EQ ADJUST/HF SHELF** TONE CONTROLS BASS TREBLE VIDEO CONTROLS 4:3 IN >16:9 DISPLAY** SETTING DOLBY CONFIG CENTER WIDTH DIMENSION PANORAMA NIGHT PLII** PLIIx** DISPLAY SETUP** CONNECTION HDMI AUDIO OUT OSD: 2-LINE OSD OSD: MENU TIME OUT F/P DISPLAY: BRIGHTNESS F/P DISPLAY: TIME OUT SETTING MV-5 Appendix D R/P CONNECTIONS HD INPUT DVD INPUT GAME INPUT SAT INPUT CABLE INPUT DVR INPUT CD INPUT DOCK INPUT PC INPUT TUNER INPUT AUX 1 INPUT AUX 2 INPUT ANALOG AUDIO DIGITAL AUDIO ANALOG VIDEO DIGITAL VIDEO DOCK NONE NONE USB D-5 Appendix D 3-DIGIT PRE-PROGRAMMED CODES WORKSHEET COMPONENT AUDIO DVD CD SAT TV VCR CABLE AUX LIGHT TAPE PHONO TV2 VCR2 DVR LDP XM RADIO IPOD X-BOX Lexicon MANUFACTURER CODE(S) USED D-6 Index Numerics 2-channel listening modes, 3-25 2-Line OSD parameter, 3-3 5. 1-channel direct inputs, 3-28 5-channel listening modes, 3-25 7. 1-channel direct inputs, 3-28 7-channel listening modes, 3-25 A A/D SAMPLE RATE parameter, 3-17 A/V SYNC DELAY parameter, 3-17 advanced video BRIGHTNESS parameter, 3-21 COLOR parameter, 3-21 COMPONENT ENHANCE parameter, 3-21 CONTRAST parameter, 3-21 DCDi INTERPOL parameter, 3-20 FILM DETECTION parameter, 3-20 FILM EDIT DETECT parameter, 3-21 FLESHTONE NR parameter, 3-21 INPUT TYPE parameter, 3-19 NOISE REDUCTION parameter, 3-20 SHARPNESS parameter, 3-19 X-COLOR SUPPRESS parameter, 3-20 ADVANCED VIDEO menu, 3-17, 3-19 ALL input parameter selection, 3-11 ANLG AUDIO parameter, 3-16 audio analog audio input setup, 3-16 AUDIO CONTROLS menu, 4-2 AUDIO STATUS menu, 4-4 digital audio input setup, 3-16 HDMI AUDIO OUT parameter, 3-3 rear panel connectors, 2-6 TONE CONTROLS parameter, 4-3 AUTO EQ parameter, 4-2 AUTO SETTINGS parameter, 3-8 autocalibration AUTO EQ parameter, 4-2 AUTO SETTINGS parameter, 3-8 EQ PRESET parameter, 4-2 FULL AUTOCAL menu, 3-6 MANUAL setup menu, 3-6, 3-8 microphone input connector, 2-7 SEMI AUTOCAL menu, 3-6 SPEAKER/EQ SETUP menu, 3-5 B BASS parameter, 4-3 battery installation, 1-4 BRIGHTNESS parameter, 3-4, 3-21 C CAL NOISE parameter, D-2­D-3 CENTER WIDTH parameter, 3-31 COLOR parameter, 3-21 command matrix, 2-11 COMPONENT ENHANCE parameter, 3-21 component rear panel connectors, 2-6 CONNECTION parameter, 3-3 CONTRAST parameter, 3-21 cross-color interference, 3-20 Customizing input names, 3-13 DIG AUDIO parameter, 3-16 DIG/ANLG AUTO parameter, 3-16 DIMENSION parameter, 3-31 DISPLAY SETUP menu, 3-2­3-3, 3-29, 3-31­3-32 dock input 2-line display characteristics, 5-5 charging the iPod, 5-6 connecting to the MV-5, 5-4 controlling the iPod, 5-6 DOCK AUTO POWER parameter, 3-32 Dock Functionality, 5-4 docking the iPod, 5-5 overview, 2-8 rear panel connector, 2-7 remote control, 5-6 removing the iPod, 5-6 ZONE 2 OUT parameter, 3-18 documentation conventions, 1-ii DOLBY configuration menu, 3-2 Dolby Dolby Digital modes, 3-24 DTS + DOLBY modes, 3-22 listening modes descriptions, 3-26 surround configuration menu, 3-29 DOWNMIX parameter selection, 3-18 DSP listening modes descriptions, 3-27 DTS DTS + DOLBY modes, 3-22 DTS modes, 3-25 listening modes descriptions, 3-26 surround configuration menu, 3-29 D DCDi INTERPOL parameter, 3-20 Declaration of Conformity, A-4 default video source settings, 3-20 E EQ ADJUST parameter, 4-3 EQ PRESET parameter, 4-2 Index F favorite channel access, C-9 setup, C-9 FILM DETECTION parameter, 3-20 FILM EDIT DETECT parameter, 3-21 FLESHTONE NR parameter, 3-21 front panel display, 2-3 front panel display BRIGHTNESS parameter, 3-4 TIME OUT parameter, 3-4 FULL AUTOCAL menu, 3-6 analog modes, 3-25 available listening modes, 3-23 descriptions, 3-26 DOLBY CONFIG menu, 3-2 Dolby Digital modes, 3-24 DSP listening modes, 3-27 DTS + DOLBY modes, 3-22 DTS modes, 3-25 LOGIC 7 DEFAULT parameter, 3-30 MODE FAMILY parameter, 3-16 MODE parameter, 3-16 PCM modes, 3-23 selecting, 3-22 SURROUND CONFIG menu, 3-2 surround configuration menu, 3-29 Logic 7 DEFAULT parameter, 3-30 listening modes descriptions, 3-26 surround configuration menu, 3-29 SETUP menu, 3-2, B-3 SPEAKER/EQ SETUP menu, 3-2, B-5 SURROUND CONFIG menu, 3-2, B-4 VIDEO CONTROLS menu, B-2 MENU TIME OUT parameter, 3-4 microphone, 3-6 MODE buttons, 2-4 MODE FAMILY parameter, 3-16 MODE parameter, 3-16, 3-31 MUTE button, 2-4 MUTE LEVELS menu, 3-2, 3-32 MV-5 About, 1-2 Available Options, 1-3 Declaration of Conformity, A-4 installation considerations, 1-4 Product Registration, 1-2 routine maintenance, 6-12 specifications, A-2 What's in the Box, 1-3 MV-5 error messages, 6-7 autocal errors, 6-8 video errors, 6-7 Lexicon H HDMI AUDIO OUT parameter, 3-3 HDMI connectors, 2-6 HF SHELF parameter, 4-3 M I INPUT parameter, 3-11 input selection buttons, 2-3 INPUT SETUP menu, 3-2, 3-13, B-6, D-2­D-3 INPUT setup parameter, 3-13 INPUT TYPE parameter, 3-19 installation considerations, 1-4 iPod iPod functionality, 5-4 Zone 2 iPod, 5-7 IR (Infra Red) front panel receiver, 2-3 rear panel connector, 2-6 Main Zone input selection buttons, 2-3 INPUT SETUP menu, 3-2 mute levels paramater, 3-32 OFF button, 2-4 maintenance, 6-12 MANUAL setup menu, 3-6, 3-8 menu AUDIO CONTROLS menu, 4-2, B-2 DISPLAY SETUP menu, 3-2­3-3, B-4 DOLBY CONFIG menu, 3-2 INPUT SETUP menu, 3-2, B-6 menu arrows, 2-9, 2-11 menu item selection, 2-9, 2-11 menu options, 2-11 MUTE LEVELS menu, 3-2 navigation, 2-9 overview, 2-9 POWER ON SETTINGS menu, 3-2 SELECT button, 2-9 N NAME parameter, 3-13 NIGHT parameter, 3-31 NOISE REDUCTION parameter, 3-20 O OSD (On-Screen Display), 3-3 MENU TIME OUT parameter, 3-4 OUTPUT LEVELS menu, 3-11 L listening modes, 3-22 5. 1-channel direct inputs, 3-28 7. 1-channel direct inputs, 3-28 P PANORAMA parameter, 3-31 PC input controls, 5-2 I-2 MV-5 overview, 2-8 playing PC media, 5-3 setting up to play, 5-2 USB connector, 2-6 ZONE 2 OUT parameter, 3-18 power AC input connector, 2-7 POWER ON SETTINGS menu, 3-2, 3-32 rear panel switch, 2-7 standby button, 2-4 preamplifier rear panel connectors, 2-7 recall pre-programming, C-4 restoring factory default settings, C-14 setup, C-3 system volume setup, C-11 transmitting icon, C-2 using the code library, C-15 restoring the factory defaults, 6-12 routine maintenance, 6-12 RS-232 connector, 2-7 Index T TEST TONE parameter, 3-11 TIME OUT parameter, 3-4 tone controls, 4-3 BASS parameter, 4-3 TREBLE parameter, 4-3 TREBLE parameter, 4-3 trigger output connectors, 2-7 TRIGGER 2 parameter, 3-17 troubleshooting, 6-2 S safety instructions, 1-ii SELECT button, 2-9 SEMI AUTOCAL menu, 3-6 SETUP menu, 3-2 SHARPNESS parameter, 3-19 SPEAKER/EQ SETUP menu, 3-5 speakers crossover setup, 3-9 FULL AUTOCAL menu, 3-6 MANUAL setup menu, 3-6, 3-8 manual TEST TONE, 3-11 output levels INPUT parameter, 3-11 OUTPUT LEVELS menu, 3-11 SEMI AUTOCAL menu, 3-6 SPEAKER DISTANCES menu, 3-10 SPEAKER/EQ SETUP menu, 3-2, 3-5 SPEAKERS manual setup menu, 3-9 SUB HPF parameter, 3-10 SUB MODE parameter, 3-10 SUB/LFE LPF parameter, 3-10 SUBWOOFERS parameter, 3-10 UNITS parameter, 3-11 specifications, A-2 Standby button, 2-4 SUB HPF parameter, 3-10 SUB MODE parameter, 3-10 SUB/LFE LPF parameter, 3-10 SUBWOOFERS parameter, 3-10 SURROUND CONFIG menu, 3-2, 3-29 R rear panel connectors, 2-6­2-7 overview, 2-5 remote control adjusting the touch screen contrast, C-7 advanced customizing tools, C-6 backlight time out, C-7 battery installation, 1-4 button learning, C-4 buttons overview, 2-10 cloning, C-11 command matrix, 2-11­2-15 customizing the touch screen, C-7 erasing commands, C-13 favorite channel access, C-9 favorite channel setup, C-9 hiding and adding pages, C-12 LCD display overview, 2-10 light button, 2-11, C-2 lock feature, C-6 macro setup, C-10 operation considerations, 2-8 optional RF-1 receiver, C-14 overview, 2-8 pre-programmed codes, C-3 pre-programmed codes worksheet, D-6 programming, C-2 punch through commands, C-11 U UNITS parameter, 3-11 V video ADVANCED VIDEO menu, 3-17, 3-19 CONNECTION parameter, 3-3 default video source settings, 3-20 rear panel connectors, 2-6 VIDEO IN setup parameter, 3-14 VIDEO OUT parameter, 3-15 video resolutions table, 6-10 VIDEO STATUS menu, 4-4 V-PROCESS parameter, 3-14 volume adjust Main Zone level, 2-3 adjust Zone 2 level, 2-3 knob, 2-3 MUTE LEVELS menu, 3-32 V-PROCESS parameter, 3-14 X X-COLOR SUPPRESS parameter, 3-20 I-3 Index Z Zone 2 input selection buttons, 2-3 INPUT SETUP menu, 3-2 iPod, 5-7 mute levels paramater, 3-32 OFF button, 2-4 rear panel connectors, 2-7 ZONE-2 OUT parameter, 3-17 Lexicon I-4 LIMITED WARRANTY Harman Specialty Group offers the following warranty on this product: What is the Duration of this Warranty?This warranty will remain in effect for three (3) years from the original date of purchase. Damage to a unit that has been altered, or on which the serial number has been defaced, modified, or removed. What are the Warranties? Limitations of Implied What Expenses will Harman Specialty Group Assume? Harman Specialty Group will pay all labor and material expenses for covered items. [. . . ]