User manual LEXICON RV-5

[. . . ] RV-5 Receiver User Guide IMPORTANT SAFETY INSTRUCTIONS Read these instructions. Install in accordance with the manufacturer's instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not defeat the safety purpose of the polarized or grounding-type plug. [. . . ] Note: If all three Preset locations indicate "FACTORY", then the AUTOCAL procedure has not yet been done, or at the least, the settings have not been saved. For more information on the AUTOCAL process, refer to Section 3: Setup. If the AUTOCAL process is performed and the settings are saved, then the Auto EQ parameter identifies if the saved AUTOCAL settings are being actively applied to the system. When the Auto EQ parameter is OFF, the AUTOCAL settings are not applied. Note: When the AUTO EQ parameter is OFF, the EQ ADJUST parameter is also not applied. EQ PRESET AUDIO CONTROLS EQ PRESET PRESET 1, PRESET 2, PRESET 3, USER Identifies the three preset locations where the AUTOCAL settings are saved, and displays the state of each preset (saved or unused). The Active PS, or Active Preset, parameter identifies the preset 4-2 RV-5 To load a different saved EQ Preset into the system: 1. Decide which saved Preset location you want to load. Select ACTIVE PS from the EQ PRESET menu. Press the or cursors to select the Preset location you want Audio Controls & Video Status Note: When the Tone Controls are OFF, the incoming audio datastream is stereo analog, and the Mode Family is set to STEREO, four different listening modes are available: 7CH STEREO, 5CH STEREO, 2CH STEREO, and 2CH BYPASS. Refer to the "Listening Modes" section of Section 3: Setup for more information. cursor to save the selection. BASS AUDIO CONTROLS BASS +6dB to -6dB When the Active PS is set to "USER", this indicates a factory default condition. Note: Once a Preset location has been selected and saved, the factory default "USER" option is no longer available for selection. Before a preset location is saved, toggling the EQ on & off results in a noticeable change in the subwoofer output level. This is normal behavior. Controls the amount of low-frequency boost or cut applied to all of the audio outputs. Bass is an independent setting for each input, NOT a global setting. The BASS parameter can be adjusted from +6dB to -6dB in 1dB increments. TREBLE AUDIO CONTROLS TREBLE +6dB to -6dB HF SHELF AUDIO CONTROLS EQ ADJUST HF SHELF +8dB to -8dB Located in the EQ ADJUST menu, the HF SHELF control acts as a high-frequency shelf filter, which boosts or cuts frequencies above 1kHz. The HF SHELF parameter can be adjusted from +8dB to -8dB in 1dB increments. Note: The HF SHELF parameter does not adjust the timbre of the rear speakers in the 7-CHANNEL listening mode. Controls the amount of high-frequency boost or cut applied to all of the audio outputs except for the subwoofers. Treble is an independent setting for each input, NOT a global setting. The TREBLE parameter can be adjusted from +6dB to -6dB in 1dB increments. TONE CONTROLS AUDIO CONTROLS TONE CONTROLS: OFF OFF, ON Activates or deactivates the Bass and Treble Tone Controls. Bass and Treble controls are only active when the Tone Control parameter is set to ON. 4-3 Audio Controls & Video Status AUDIO STATUS AUDIO CONTROLS AUDIO STATUS INPUT: HD+ NAME: CONNECTOR: ANALOG 3 AUDIO: - - MODE FAMILY: LOGIC 7 MODE: MUSIC 5. 1 Lexicon · · · · INPUT RESOL identifies the current input resolution setting. COPY PROTECTION identifies the current status of copy protection. V-PROCESS identifies the current setting of the video processor. OUTPUT RESOL identifies the current output resolution setting of the HDMI and component outputs. [. . . ] D-2 3-Digit Preprogrammed Codes Worksheet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-6 Appendix D INSTALLATION WORKSHEET INPUT SETUP NAME VIDEO IN V-PROCESS VIDEO OUT HDMI LINK DIG AUDIO ANLG AUDIO DIG/ANLG AUTO MODE FAMILY** MODE** DEFAULT SUR** A/D SAMPLE RATE A/V SYNC DELAY TRIGGER 2 ZONE2 OUT** ADVANCED VIDEO INPUT TYPE SHARPNESS NOISE REDUCTION X-COLOR SUPPRESS DCDi INTERPOL FILM DETECTION FILM EDIT DETECTION FLESHTONE NR D-2 NONE DOCK N/A USB NONE N/A NONE TUNER N/A Lexicon HD DVD GAME SAT CABLE DVR CD DOCK PC TUNER AUX1 AUX2 RV-5 Appendix D HD DVD GAME SAT CABLE DVR CD DOCK PC TUNER AUX1 AUX2 INPUT SETUP COMPNT ENHANCE BRIGHTNESS CONTRAST COLOR ADVANCED VIDEO (CONTINUED) SPEAKER SETUP REAR AMP**: _______ CROSS-OVER POINTS** DISTANCES (UNITS: ___)** OUTPUT LEVELS "ALL" INPUT** HD INPUT DVD INPUT GAME INPUT SAT INPUT CABLE INPUT DVR INPUT CD INPUT DOCK INPUT PC INPUT TUNER INPUT AUX 1 INPUT AUX 2 INPUT AUTO SETTING FRONT LEFT ** CENTER FRONT RIGHT SIDE LEFT SIDE RIGHT REAR LEFT REAR RIGHT SUB/ SUB/ LFE LPF LFE HPF SUB 1 SUB 2 D-3 Appendix D SURROUND CONFIGURATION LOGIC 7 DEFAULT** DTS** DTS 96/24 DTS + NEO:6 DTS-ES MATRIX DTS-ES DISCRETE LOGIC 7 STEREO DOWN MIX DOLBY 2. 0** DOLBY PLII DOLBY PLIIx DOLBY VIRTUAL LOGIC 7 DOLBY MULTI-CHANNEL** DOLBY VIRTUAL LOGIC 7 STEREO DOWN MIX PCM 44. 1/48 kHz** LOGIC 7 DOLBY PLII DOLBY PLIIx DOLBY VIRTUAL DTS NEO:6 HALL 5/7 CH STEREO PCM 96 kHz** LOGIC 7 DOLBY PLII DOLBY PLIIx DTS NEO:6 5/7 CH STEREO D-4 Lexicon NO YES AUDIO CONTROLS AUTO EQ** ACTIVE EQ PRESET** EQ ADJUST/HF SHELF** TONE CONTROLS BASS TREBLE VIDEO CONTROLS 4:3 IN >16:9 DISPLAY** SETTING DOLBY CONFIG CENTER WIDTH DIMENSION PANORAMA NIGHT PLII** PLIIx** DISPLAY SETUP** CONNECTION HDMI AUDIO OUT OSD: 2-LINE OSD OSD: MENU TIME OUT F/P DISPLAY: BRIGHTNESS F/P DISPLAY: TIME OUT SETTING RV-5 Appendix D R/P CONNECTIONS HD INPUT DVD INPUT GAME INPUT SAT INPUT CABLE INPUT DVR INPUT CD INPUT DOCK INPUT PC INPUT TUNER INPUT AUX 1 INPUT AUX 2 INPUT ANALOG AUDIO DIGITAL AUDIO ANALOG VIDEO DIGITAL VIDEO DOCK NONE TUNER NONE USB NONE TUNER PRESET 01 02 03 04 05 06 07 08 FREQ / BAND TUNER PRESET 09 10 11 12 13 14 15 16 FREQ / BAND TUNER PRESET 17 18 19 20 21 22 23 24 FREQ / BAND TUNER PRESET 25 26 27 28 29 30 FREQ / BAND D-5 Appendix D 3-DIGIT PRE-PROGRAMMED CODES WORKSHEET COMPONENT AUDIO DVD CD SAT TV VCR CABLE AUX LIGHT TAPE PHONO TV2 VCR2 DVR LDP XM RADIO IPOD X-BOX Lexicon MANUFACTURER CODE(S) USED D-6 Index Numerics 2-channel listening modes, 3-26 2-Line OSD parameter, 3-3 5. 1-channel direct inputs, 3-29 5-channel listening modes, 3-26 7. 1-channel direct inputs, 3-29 7-channel listening modes, 3-26 A A/D SAMPLE RATE parameter, 3-18 A/V SYNC DELAY parameter, 3-18 advanced video BRIGHTNESS parameter, 3-22 COLOR parameter, 3-22 COMPONENT ENHANCE parameter, 3-22 CONTRAST parameter, 3-22 DCDi INTERPOL parameter, 3-21 FILM DETECTION parameter, 3-21 FILM EDIT DETECT parameter, 3-22 FLESHTONE NR parameter, 3-22 INPUT TYPE parameter, 3-20 NOISE REDUCTION parameter, 3-21 SHARPNESS parameter, 3-20 X-COLOR SUPPRESS parameter, 3-21 ADVANCED VIDEO menu, 3-18, 3-20 ALL input parameter selection, 3-12 AM/FM radio tuner, 5-2 amplifier making connections, 2-8 output connectors, 2-7 overview, 2-8 REAR AMP parameter, 3-6 utilizing spare channels, 2-8 ANLG AUDIO parameter, 3-17 audio analog audio input setup, 3-17 AUDIO CONTROLS menu, 4-2 AUDIO STATUS menu, 4-4 digital audio input setup, 3-16 HDMI AUDIO OUT parameter, 3-3 rear panel connectors, 2-6 TONE CONTROLS parameter, 4-3 AUTO EQ parameter, 4-2 AUTO SETTINGS parameter, 3-9 autocalibration AUTO EQ parameter, 4-2 AUTO SETTINGS parameter, 3-9 EQ PRESET parameter, 4-2 FULL AUTOCAL menu, 3-7 MANUAL setup menu, 3-6, 3-9 microphone input connector, 2-6 SEMI AUTOCAL menu, 3-6 SPEAKER/EQ SETUP menu, 3-5 D DCDi INTERPOL parameter, 3-21 Declaration of Conformity, A-4 default video source settings, 3-21 DIG AUDIO parameter, 3-16 DIG/ANLG AUTO parameter, 3-17 DIMENSION parameter, 3-32 DISPLAY SETUP menu, 3-2­3-3, 3-30, 3-32­3-33 dock input 2-line display characteristics, 5-7 charging the iPod, 5-9 connecting to the RV-5, 5-6 controlling the iPod, 5-8 DOCK AUTO POWER parameter, 3-33 Dock Functionality, 5-6 docking the iPod, 5-7 front panel controls, 5-8 overview, 2-9, 5-2 rear panel connector, 2-8 remote control, 5-8 removing the iPod, 5-9 ZONE 2 OUT parameter, 3-19 documentation conventions, 1-ii Dolby Dolby Digital modes, 3-25 DTS + DOLBY modes, 3-23 listening modes descriptions, 3-27 surround configuration menu, 3-30 DOLGY configuration menu, 3-2 DOWNMIX parameter selection, 3-18 DSP listening modes descriptions, 3-28 DTS DTS + DOLBY modes, 3-23 DTS modes, 3-26 listening modes descriptions, 3-27 surround configuration menu, 3-30 B BASS parameter, 4-3 battery installation, 1-4 BRIGHTNESS parameter, 3-4, 3-22 C CAL NOISE parameter, D-2­D-3 CENTER WIDTH parameter, 3-32 COLOR parameter, 3-22 command matrix, 2-12 COMPONENT ENHANCE parameter, 3-22 component rear panel connectors, 2-7 CONNECTION parameter, 3-3 CONTRAST parameter, 3-22 cross-color interference, 3-21 Customizing input names, 3-15 Index E EQ ADJUST parameter, 4-3 EQ PRESET parameter, 4-2 Lexicon L listening modes, 3-23 5. 1-channel direct inputs, 3-29 7. 1-channel direct inputs, 3-29 analog modes, 3-26 available listening modes, 3-24 descriptions, 3-27 DOLBY CONFIG menu, 3-2 Dolby Digital modes, 3-25 DSP listening modes, 3-28 DTS + DOLBY modes, 3-23 DTS modes, 3-26 LOGIC 7 DEFAULT parameter, 3-31 MODE FAMILY parameter, 3-17 PCM modes, 3-24 selecting, 3-23 SURROUND CONFIG menu, 3-2 surround configuration menu, 3-30 Logic 7 DEFAULT parameter, 3-31 listening modes descriptions, 3-27 surround configuration menu, 3-30 F favorite channel access, C-9 setup, C-9 FILM DETECTION parameter, 3-21 FILM EDIT DETECT parameter, 3-22 FLESHTONE NR parameter, 3-22 front panel display, 2-3 front panel display BRIGHTNESS parameter, 3-4 TIME OUT parameter, 3-4 FULL AUTOCAL menu, 3-7 navigation, 2-10 overview, 2-10 POWER ON SETTINGS menu, 3-2 SELECT button, 2-10 SETUP menu, 3-2, B-3 SPEAKER/EQ SETUP menu, 3-2, B-5 SURROUND CONFIG menu, 3-2, B-4 VIDEO CONTROLS menu, B-2 MENU TIME OUT parameter, 3-4 microphone, 3-6 MODE buttons, 2-4 MODE FAMILY parameter, 3-17 MODE parameter, 3-32 MUTE button, 2-4 MUTE LEVELS menu, 3-2, 3-33 N NAME parameter, 3-14 NIGHT parameter, 3-32 NOISE REDUCTION parameter, 3-21 H HDMI AUDIO OUT parameter, 3-3 HDMI connectors, 2-7 HF SHELF parameter, 4-3 O M Main Zone input selection buttons, 2-3 INPUT SETUP menu, 3-2 mute levels paramater, 3-33 OFF button, 2-4 maintenance, 6-12 MANUAL setup menu, 3-6, 3-9 menu AUDIO CONTROLS menu, 4-2, B-2 DISPLAY SETUP menu, 3-2­3-3, B-4 DOLBY CONFIG menu, 3-2 INPUT SETUP menu, 3-2, B-6 menu arrows, 2-10, 2-12 menu item selection, 2-10, 2-12 menu options, 2-12 MUTE LEVELS menu, 3-2 OSD (On-Screen Display), 3-3 MENU TIME OUT parameter, 3-4 OUTPUT LEVELS menu, 3-12 I INPUT parameter, 3-12 input selection buttons, 2-3 INPUT SETUP menu, 3-2, 3-14, B-6, D-2­D-3 INPUT setup parameter, 3-14 INPUT TYPE parameter, 3-20 installation considerations, 1-4 installation worksheet, 2 IR (Infra Red) front panel receiver, 2-3 rear panel connector, 2-7 P PANORAMA parameter, 3-32 PC input controls, 5-4 overview, 2-9, 5-2 playing PC media, 5-5 setting up to play, 5-4 USB connector, 2-6 ZONE 2 OUT parameter, 3-19 I-2 RV-5 power AC input connector, 2-7 POWER ON SETTINGS menu, 3-2, 3-33 rear panel switch, 2-7 standby button, 2-4 preamplifier rear panel connectors, 2-6, 2-8 system volume setup, C-11 transmitting icon, C-2 using the code library, C-15 restoring the factory defaults, 6-12 routine maintenance, 6-12 RS-232 connector, 2-6 RV-5 About, 1-2 Available Options, 1-3 Declaration of Conformity, A-4 installation considerations, 1-4 Product Registration, 1-2 routine maintenance, 6-12 specifications, A-2 What's in the Box, 1-3 RV-5 error messages, 6-7 autocal errors, 6-8 video errors, 6-7 SUBWOOFERS parameter, 3-11 UNITS parameter, 3-12 specifications, A-2 Standby button, 2-4 SUB HPF parameter, 3-11 SUB MODE parameter, 3-11 SUB/LFE LPF parameter, 3-11 SUBWOOFERS parameter, 3-11 SURROUND CONFIG menu, 3-2, 3-30 Index R REAR AMP parameter, 3-6 rear panel connectors, 2-6­2-7 overview, 2-5 remote control adjusting the touch screen contrast, C-7 advanced customizing tools, C-6 backlight time out, C-7 battery installation, 1-4 button learning, C-4 buttons overview, 2-11 cloning, C-11 command matrix, 2-12­2-16 customizing the touch screen, C-7 erasing commands, C-13 favorite channel access, C-9 favorite channel setup, C-9 hiding and adding pages, C-12 LCD display overview, 2-11 light button, 2-12, C-2 lock feature, C-6 macro setup, C-10 operation considerations, 2-9 optional RF-1 receiver, C-14 overview, 2-9 pre-programmed codes, C-3 pre-programmed codes worksheet, D-6 programming, C-2 punch through commands, C-11 recall pre-programming, C-4 restoring factory default settings, C-14 setup, C-3 T TEST TONE parameter, 3-12 TIME OUT parameter, 3-4 tone controls, 4-3 BASS parameter, 4-3 TREBLE parameter, 4-3 TREBLE parameter, 4-3 trigger output connectors, 2-6 TRIGGER 2 parameter, 3-18 troubleshooting, 6-2 tuner activation & display, 5-2 AM/FM radio tuner, 5-2 antenna connectors, 2-8 control button overview, 2-3 controls, 5-3 overview, 2-9, 5-2 ZONE 2 OUT parameter, 3-19 Zone 2 tuner, 5-2, 5-9 S safety instructions, 1-ii SELECT button, 2-10 SEMI AUTOCAL menu, 3-6 SETUP menu, 3-2 SHARPNESS parameter, 3-20 SPEAKER/EQ SETUP menu, 3-5 speakers crossover setup, 3-10 FULL AUTOCAL menu, 3-7 MANUAL setup menu, 3-6, 3-9 manual TEST TONE, 3-12 output levels INPUT parameter, 3-12 OUTPUT LEVELS menu, 3-12 SEMI AUTOCAL menu, 3-6 SPEAKER DISTANCES menu, 3-11 SPEAKER/EQ SETUP menu, 3-2, 3-5 SPEAKERS manual setup menu, 3-10 SUB HPF parameter, 3-11 SUB MODE parameter, 3-11 SUB/LFE LPF parameter, 3-11 U UNITS parameter, 3-12 I-3 Index V video ADVANCED VIDEO menu, 3-18, 3-20 CONNECTION parameter, 3-3 default video source settings, 3-21 rear panel connectors, 2-7 VIDEO IN setup parameter, 3-15 VIDEO OUT parameter, 3-16 video resolutions table, 6-10 VIDEO STATUS menu, 4-4 V-PROCESS parameter, 3-15 volume adjust Main Zone level, 2-3 adjust Zone 2 level, 2-3 knob, 2-3 MUTE LEVELS menu, 3-33 V-PROCESS parameter, 3-15 Lexicon X X-COLOR SUPPRESS parameter, 3-21 Z Zone 2 input selection buttons, 2-3 INPUT SETUP menu, 3-2 mute levels paramater, 3-33 OFF button, 2-4 radio tuner, 5-2, 5-9 rear panel connectors, 2-6 ZONE-2 OUT parameter, 3-18 I-4 LIMITED WARRANTY Harman Specialty Group offers the following warranty on this product: What is the Duration of this Warranty?This warranty will remain in effect for three (3) years from the original date of purchase. Damage to a unit that has been altered, or on which the serial number has been defaced, modified, or removed. What are the Warranties? Limitations of Implied What Expenses will Harman Specialty Group Assume? Harman Specialty Group will pay all labor and material expenses for covered items. [. . . ]