User manual LEXICON RV-8 REV 0

[. . . ] LX Power Amplifier RV-8 Receiver User Guide User Guide IMPORTANT SAFETY INSTRUCTIONS 1. Install in accordance with the manufacturer's instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or another apparatus (including amplifiers) that produces heat. Do not defeat the safety purpose of the polarized or grounding-type plug. [. . . ] When set to ON, the RV-8 activates an internal calibration noise signal to set the limiter. When set to OFF, the RV-8 deactivates the internal calibration noise test signal. An external calibration source such as an audio calibration disc is required to generate a noise signal to set the bass peak limiter. Parameter CAL NOISE LIMITER LIMIT ADJ 3-46 RV-8 SETUP (continued from page 3-46) SETUP INPUTS SPEAKERS I/O CONFIG DISPLAYS VOLUME CONTROLS TRIGGER TUNER SETUP LOCK OPTIONS SPEAKER SETUP CUSTOM SETUP THX SETUP SPEAKER DISTANCES LEVELS CALIBRATION R 0. 0dB C 0. 0dB M SUB 0. 0dB L 0. 0dB SL 0. 0dB RL 0. 0dB SR 0. 0dB RR 0. 0dB BASS PEAK LIMITER MAIN MENU MODE ADJUST AUDIO CONTROLS TUNER PRESETS SETUP LEVELS CALIBRATION INTERNAL NOISE TEST EXTERNAL NOISE TEST BASS PEAK LIMITER BASS PEAK LIMITER CAL NOISE ON LIMITER ON SUB LIMITER LIMIT ADJ 75dB !CAUTION!HIGH AUDIO LEVELS ON OFF LIMITER SETUP SPEAKERS LEVELS CALIBRATION BASS PEAK LIMITER ON, OFF LIMITER LIMIT ADJ SETUP SPEAKERS LEVELS CALIBRATION 75dB to 120dB BASS PEAK LIMITER LIMIT ADJ Limits output signals for the Main Zone audio output connector labeled Sub, as well as other Main Zone speaker and audio output connectors to which low-frequency signals are redirected. When set to ON, the RV-8 restricts output signals to the level specified in the BASS PEAK LIMITER menu LIMIT ADJ parameter. When set to OFF, the RV-8 does not restrict output levels, regardless of the LIMIT ADJ parameter setting. Specifies the output level restriction placed on the Main Zone audio output connector labeled Sub, as well as other Main Zone speaker and audio output connectors to which low-frequency signals are redirected. This restriction is applied when the BASS PEAK LIMITER menu LIMITER parameter is set to ON. When the LIMIT ADJ parameter is selected, it is automatically set to 75dB. MAIN MENU MODE ADJUST AUDIO CONTROLS TUNER PRESETS SETUP SETUP INPUTS SPEAKERS I/O CONFIG DISPLAYS VOLUME CONTROLS TRIGGER TUNER SETUP LOCK OPTIONS SPEAKER SETUP CUSTOM SETUP THX SETUP SPEAKER DISTANCES LEVELS CALIBRATION R 0. 0dB C 0. 0dB M SUB 0. 0dB L 0. 0dB SL 0. 0dB RL 0. 0dB SR 0. 0dB RR 0. 0dB LEVELS CALIBRATION INTERNAL NOISE TEST EXTERNAL NOISE TEST BASS PEAK LIMITER BASS PEAK LIMITER BASS PEAK LIMITER CAL NOISE ON LIMITER ON SUB LIMIT ADJ 100dB LIMIT ADJ 75dB !CAUTION!HIGH AUDIO LEVELS 75 to 120dB 3-47 SETUP MAIN MENU MODE ADJUST AUDIO CONTROLS TUNER PRESETS SETUP SETUP INPUTS SPEAKERS I/O CONFIG REAR PANEL CONFIG DISPLAYS VOLUME CONTROLS TRIGGER TUNER SETUP LOCK OPTIONS I/O CONFIG ANALOG INPUTS AMP OUTPUTS REAR PANEL CONFIG 8 STEREO INPUTS OR 5 ST & (1) 5. 1 ANLG OR 2 ST & (2) 5. 1 ANLG Lexicon I/O CONFIG SETUP I/O CONFIG labeled 6, 7 and 8 are reassigned to the stereo connectors labeled 6, 7 and 8. Selecting the SETUP menu I/O CONFIG option opens the I/O CONFIG menu shown above, which can be used to configure the analog audio input connectors as eight stereo connectors, five stereo and one 5. 1-channel connectors, or two stereo and two 5. 1channel connectors. The I/O CONFIG menu can also be used to configure the amplifier outputs. 5 ST & (1) 5. 1 ANLG SETUP I/O CONFIG ANALOG INPUTS 5 ST & (1) 5. 1 ANLG Configures the analog audio input connectors as five stereo and one 5. 1-channel connectors. When the analog audio input connectors are configured as five stereo and one 5. 1-channel connectors: · 8 STEREO INPUTS SETUP I/O CONFIG ANALOG INPUTS 8 STEREO INPUTS The connectors labeled 1, 2, 3, 4, and 5 are configured as stereo connectors. The connectors labeled 6, 7, and 8 are configured as a 5. 1-channel connector. This connector is sent to the Main Zone speaker and audio output connectors as indicated in the table on the next page. Two-channel sources that were assigned to the stereo connectors labeled 6, 7, and 8 are reassigned to the 5. 1-channel connector labeled 6, 7, and 8. The 5. 1-channel connectors should only be used with 5. 1-channel analog sources such as DVD-As and SACDs. Configures the analog audio input connectors as eight stereo connectors, which is the factory-default configuration. When the analog audio input connectors are configured as eight stereo connectors: · · All connectors are configured as stereo connectors. Neither of the 5. 1-channel connectors is available. Sources that were assigned to the 5. 1-channel connector labeled 3, 4 and 5 are reassigned to the stereo connectors labeled 3, 4 and 5. Sources that were assigned to the 5. 1-channel connector · · 3-48 RV-8 SETUP Input Connector ANALOG INPUTS 2 ST & (2) 5. 1 ANLG 2 ST & (2) 5. 1 ANLG SETUP I/O CONFIG Output Connectors Front L Front R Center Sub Side L and Rear L Side R and Rear R (L) (R) (C) (SUB) (LS) (RS) Configures the analog audio input connectors as two stereo and two 5. 1-channel connectors. When the analog audio input connectors are configured as two stereo and two 5. 1-channel connectors: · · The connectors labeled 1 and 2 are configured as stereo connectors. The connectors labeled 3, 4 and 5 are configured as a 5. 1channel connector, and the connectors labeled 6, 7, and 8 are configured as a second 5. 1-channel connector. These connectors are sent to the Main Zone speaker and audio output connectors as indicated in the table to the right. [. . . ] Claims for shipping damages must be made with the carrier. Damage to a unit that has been altered, or on which the serial number has been defaced, modified, or removed. Include a copy of the original dated sales receipt. (A copy of the original dated sales receipt must be presented whenever warranty service is required. ) Do not include accessories such as power cords or user guides unless instructed to do so. [. . . ]