User manual LEXMARK 310

[. . . ] Contents Understanding your printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Printer parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Loading paper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] For compatible print cartridges, see "Ordering supplies" on page 30. · A memory card for photos or a PictBridge-enabled camera with a USB cable. For compatible memory cards, see "Supported memory cards" on page 11. Packing the printer 1 Turn the printer off. 2 Remove all photo paper from the paper support. 3 Close the paper support. 4 Remove any memory cards from the memory card slots. 26 5 Disconnect the power cord. 1 2 6 Raise the carry handle. Note: When traveling with your printer, it is not necessary to remove the print cartridge. Warning: Always travel with the printer in the upright position. 27 Unpacking the printer 1 Place the printer on a flat, level surface. 2 Lower the carrying handle. 3 Connect the power cord. 2 1 4 Press Power. Make sure the power light and display are on. 5 Lift the paper support. 28 6 Load photo paper. The printer is now ready to print your photos. Insert a memory card containing photos or connect your PictBridge-enabled camera to the printer. 29 Maintaining your print cartridge Checking the ink level status 1 Press Menu. The Photo menu appears. 2 Press the down arrow button until you highlight Ink Levels. 3 Press Select. Note: Press Stop/Clear to return to the previous menu. If you need to order a new print cartridge, see "Ordering supplies" on page 30. Refilling the print cartridge Lexmark's warranty does not cover the repair of failures or damage caused by a refilled cartridge. We do not recommend use of a refilled cartridge. Refilling a cartridge can affect print quality and cause damage to the printer. Use Lexmark supplies for the best results. See "Ordering supplies" on page 30. Ordering supplies To order printer supplies or to locate a dealer near you, contact the Lexmark Web site at www. lexmark. com. Color print cartridges · 33 · 35 30 Replacing the print cartridge Removing a used print cartridge 1 If the printer is off, press the Power button. 2 Open the access cover. 3 Press down on the cartridge lever to open the cartridge lid. 31 4 Remove the old cartridge. Installing a print cartridge 1 If you are installing a new print cartridge, remove the sticker and transparent tape from the bottom of the print cartridge. 1 2 Warning: Do not touch the gold contact area on the back or the nozzles on the bottom of the cartridge. 2 Unless it is already open, press down on the cartridge lever to open the cartridge lid. 32 3 Insert the cartridge. 4 Snap the lid closed. 5 Close the access cover. 6 Load a blank 4x6 index card into the paper support. 7 When prompted on the display, press Select to print the cartridge alignment page. Note: You may discard this page after it prints. 33 Aligning the print cartridge 1 Load a blank 4x6 index card. 2 Press Menu. The Photo menu appears. 3 Press the down arrow button until you highlight Align Cartridge. 4 Press Select. Note: Discard the index card after it prints. Cleaning the print cartridge nozzles 1 Load a blank 4x6 index card. 2 Press Menu. The Photo menu appears. 3 Press the down arrow button until you highlight Clean Cartridge. 34 4 Press Select. Note: Discard the index card after it prints. Printing a test page 1 Load a blank 4x6 index card. 2 Press Menu. The Photo menu appears. 3 Press the down arrow button until you highlight Print Test Page. 4 Press Select. Note: Discard the index card after it prints. 35 Troubleshooting Category "Setup troubleshooting" on page 37 "Print troubleshooting" on page 38 "Improving print quality" on page 40 "Jams and misfeeds troubleshooting" on page 43 "Memory card and PictBridge troubleshooting" on page 44 "Error messages troubleshooting" on page 45 Purpose Resolves issues that occur during the initial printer setup. Resolves issues that occur while printing. Resolves issues with the print quality of your photos. [. . . ] Any questions regarding this compliance information statement should be directed to: Director of Lexmark Technology & Services Lexmark International, Inc. 740 West New Circle Road Lexington, KY 40550 (859) 232-3000 Industry Canada compliance statement This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Avis de conformité aux normes de l'industrie du Canada Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. European Community (EC) directives conformity This product is in conformity with the protection requirements of EC Council directives 89/336/ EEC and 73/23/EEC on the approximation and harmonization of the laws of the Member States relating to electromagnetic compatibility and safety of electrical equipment designed for use within certain voltage limits. A declaration of conformity with the requirements of the directives has been signed by the Director of Manufacturing and Technical Support, Lexmark International, S. A. , Boigny, France. This product satisfies the Class B limits of EN 55022 and safety requirements of EN 60950. 48 Japanese VCCI notice If this symbol appears on your product, the accompanying statement is applicable. Korean MIC statement If this symbol appears on your product, the accompanying statement is applicable. This equipment has undergone EMC registration as a household product. [. . . ]