User manual LEXMARK C522

[. . . ] C520, C522, and C524 User's Guide Lexmark and Lexmark with diamond design are trademarks of Lexmark International, Inc. , registered in the United States and/or other countries. 740 West New Circle Road Lexington, Kentucky 40550 June 2005 www. lexmark. com Edition: June 2005 The following paragraph does not apply to any country where such provisions are inconsistent with local law: LEXMARK INTERNATIONAL, INC. , PROVIDES THIS PUBLICATION "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some states do not allow disclaimer of express or implied warranties in certain transactions; therefore, this statement may not apply to you. This publication could include technical inaccuracies or typographical errors. [. . . ] Place the guide to rest gently against the left side of the media. Do not force the guide against the media or it could be damaged. 1 2 Load one sheet of media. Load the media so it fits flush with the right side of the manual feed slot. Load an envelope with the flap up and to the left. The orientation of the envelope is the same as when the multipurpose feeder is loaded. For an illustration, see page 56. 3 Push the media in until it stops. The printer pulls the media in farther. Identifying the multipurpose feeder or the manual feed slot 58 Loading media Using the standard bin The standard bin holds up to 250 sheets of 20 lb paper and is located on top of the printer. The standard bin collates print jobs face-down. The standard bin supports all media listed in Media sizes and support. Attaching the standard bin To attach the standard bin to the top of the printer: 1 2 Align it with the opening and slide it down. Press it down into place. Using the standard bin 59 Loading media Using the media stop The standard bin has a media stop which is used to keep media from sliding off the back of the standard bin. It has two lengths, one for shorter media like Letter and A4 sizes, and one for longer media like Legal size. To extend the media stop for short sizes of media: 1 Grasp the media stop at the first indentation. 2 Lift it up and then back until it stops at a 90 degree angle. To close it, fold it back down. Using the standard bin 60 Loading media To extend the media stop for longer sizes of media, start with the media stop fully closed: 1 Grasp the media stop at the second indentation. 2 Lift it up and back until it is flat at a 180 degree angle. Using the standard bin 61 Loading media 3 Lift up and then back on the extension until it stops at a 90 degree angle. To close the media stop, fold the extension forward and down. Raise the media stop, and then fold it back down into its closed position. Setting the Paper Type and Paper Size After setting the Paper Type and Paper Size to the correct values for the type and size used in the trays, then any trays containing the same size and type are automatically linked by the printer. Note: If the size of the media being loaded now is the same size as the media previously loaded, do not change the Paper Size setting. To change the Paper Size and Paper Type setting: 1 2 3 4 5 6 7 Make sure the printer is on and the Ready message appears. Press and release Press Press Press until until . . Paper Size/Type appears, and then press until the needed media source is reached, and then press Press to scroll through a list of possible paper sizes to locate the correct size, and then press . Press or to scroll through a list of possible paper types to locate the correct type, and then press . This saves this setting as the new user default type or size setting. The message Submitting Selection appears. The printer returns to the Paper Menu. 8 Press twice to return to Ready. Setting the Paper Type and Paper Size 62 7 Clearing jams Avoiding jams hints The following hints can help avoid jams: · Use only recommended paper or specialty media (referred to as media). See Media guidelines for more information. See the Card Stock & Label Guide available on the Lexmark Web site at www. lexmark. com/publications for more information about which media will provide optimum results for the printing environment. [. . . ] The replacement may be a new or repaired item. The replacement item assumes the remaining warranty period of the original product. Replacement is not available to you if the product you present for exchange is defaced, altered, in need of a repair not included in warranty service, damaged beyond repair, or if the product is not free of all legal obligations, restrictions, liens, and encumbrances. Before you present this product for warranty service, remove all print cartridges, programs, data, and removable storage media (unless directed otherwise by Lexmark). [. . . ]