User manual LEXMARK C920

[. . . ] Lexmark C920 User's Guide March 2005 www. lexmark. com Lexmark and Lexmark with diamond design are trademarks of Lexmark International, Inc. , registered in the United States and/or other countries. 740 West New Circle Road Lexington, Kentucky 40550 Edition: March 2005 The following paragraph does not apply to any country where such provisions are inconsistent with local law: LEXMARK INTERNATIONAL, INC. , PROVIDES THIS PUBLICATION "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some states do not allow disclaimer of express or implied warranties in certain transactions; therefore, this statement may not apply to you. This publication could include technical inaccuracies or typographical errors. [. . . ] Partial sheets may cause labels to peel off during printing, resulting in a jam. Partial sheets also contaminate the printer and the cartridge with adhesive, and could void the printer and cartridge warranties. Use labels that can withstand temperatures of 230°C (446°F) without sealing, excessive curling, wrinkling, or releasing hazardous emissions. Do not print within 1 mm (0. 04 in. ) of the edge of the label, of the perforations, or between die-cuts of the label. Do not use label sheets that have adhesive to the edge of the sheet. Zone coating of the adhesive at least 1 mm (0. 04 in. ) away from edges is recommended. Adhesive material contaminates the printer and could void the warranty. If zone coating of the adhesive is not possible, remove a 3 mm (0. 125 in. ) strip on the leading and driver edge, and use a non-oozing adhesive. Remove a 3 mm (0. 125 in. ) strip from the leading edge to prevent labels from peeling inside the printer. Portrait orientation is preferred, especially when printing bar codes. Do not use labels that have exposed adhesive. · · · · For detailed information on label printing, characteristics, and design, see the Card Stock & Label Guide, available on the Lexmark Web site at www. lexmark. com/publications. Storing paper 76 Media specifications Card stock Card stock is single ply, and has a large array of properties, such as the moisture content, thickness, and texture, that can significantly affect print quality. See Identifying media sources and specifications for information on the preferred weight for the grain direction of media. Try a sample of any card stock considered for use with the printer before purchasing a large quantity. See Media types and weights for information on the preferred weight of media. When printing on card stock: · Set the Paper Type menu item in the Paper Menu to Card Stock from the operator panel, from the printer driver, or from MarkVision Professional. Set the Paper Weight to CardStock Weight, and select the CardStock Weight as Normal or Heavy for the value. Set this from the operator panel, the printer driver, or from MarkVision Professional. Use Heavy for card stock weighing more than or heavier than 163 g/m2 (90 lb). Be aware that preprinting, perforation, and creasing can significantly affect the print quality and cause media handling or jamming problems. Avoid using card stock that may release hazardous emissions when heated. Do not use preprinted card stock manufactured with chemicals that may contaminate the printer. Preprinting introduces semi-liquid and volatile components into the printer. [. . . ] Remote technical support is provided for this product throughout its warranty period. For products no longer covered by a Lexmark warranty, technical support may not be available or only be available for a fee. Extent of limited warranty Lexmark does not warrant uninterrupted or error-free operation of any product or the durability or longevity of prints produced by any product. Warranty service does not include repair of failures caused by: · Modification or unauthorized attachments · Accidents, misuse, abuse or use inconsistent with Lexmark user's guides, manuals, instructions or guidance. · Unsuitable physical or operating environment · Maintenance by anyone other than Lexmark or a Lexmark authorized servicer · Operation of a product beyond the limit of its duty cycle · Use of printing media outside of Lexmark specifications · Modification, refurbishment, repair, refilling or remanufacture of products by a third party, supplies or parts. [. . . ]