User manual LEXMARK E234

[. . . ] E234, E234n User's Reference May 2004 www. lexmark. com Lexmark and Lexmark with diamond design are trademarks of Lexmark International, Inc. , registered in the United States and/or other countries. 740 West New Circle Road Lexington, Kentucky 40550 Contents Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Edition notice. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] What you can do: · · · Load media into tray 1 or the optional 550-sheet tray and press Continue to resume printing. Check that the media is loaded correctly in tray 1 or the optional 550-sheet tray. Press Cancel to cancel the print job. Using the operator panel 58 Load manual feeder Light sequence: · · Continue--On Load Paper--Blink What this light sequence means: The printer prompts you to load a single sheet of media in the manual feed. What you can do: · · · Load media, with the side to be printed facing the front of the printer, into the manual feed. to reset the printer. Press and hold Cancel Print side two of a duplex job Light sequence: · · Continue--Blink Load Paper--On What this light sequence means: Print the other side of your duplex print job. What you can do: · Reinsert your print job in tray 1 using the instructions in the driver pop-up menu to orient the pages correctly. Press Continue · to resume printing. to reset the printer. Press and hold Cancel Using the operator panel 59 Invalid engine code / Invalid network code Light sequence: · · Ready--On Error--On What this light sequence means: The code in an internal print server has not been programmed, or the programmed code is not valid. What you can do: Download valid network code to the internal print server. Press Continue twice quickly to see the secondary error code. See "Secondary error codes" on page 66 for more information. Toner low Light sequence: · Toner Low/Replace PC Kit--On What this light sequence means: The printer is ready to receive and process data. In addition, the toner in the toner cartridge is getting low. What you can do: · · · · Press Continue to print the menu settings page for a list of current printer settings. Remove the toner cartridge and shake it to extend the life of the cartridge. (See "How to change a toner cartridge" on page 104 for help. ) Press and hold Cancel to reset the printer. Note: This light may not come on if the starter toner cartridge is installed in a base printer model. Using the operator panel 60 Photoconductor kit near full Light sequence: · · Continue--On Toner Low/Replace PC Kit--Blink What this light sequence means: The photoconductor kit's drum is almost full and will need replacing soon. Note: The Toner Alarm (see page 99) must be turned on for this message to appear. What you can do: · · Press Continue to resume printing. See "How to change a photoconductor kit" on page 108 for more information. Replace photoconductor kit Light sequence: · Toner Low/Replace PC Kit--Blink What this light sequence means: The photoconductor kit's drum is full and needs replacing. What you can do: · · Press Continue to resume printing. See "How to change a photoconductor kit" on page 108 for more information. Using the operator panel 61 Replace photoconductor kit (printer hard stop) Light sequence: · · · Continue--On Toner Low/Replace PC Kit--Blink Error--Blink What this light sequence means: The photoconductor kit's drum is full and needs replacing. The printer will not print any more pages until the photoconductor kit is replaced. What you can do: Replace the photoconductor kit. [. . . ] · The Toner Darkness setting is too dark. · The toner cartridge is defective. Toner rubs off the paper easily when you handle the sheets Gray background ABCDE ABCDE ABCDE * To replace the fuser, call a service technician. This setting can be changed using the Local Printer Setup Utility. See "Using the Local Printer Settings Utility" on page 99 for more information. Troubleshooting 115 Symptom Uneven print density Cause · The toner cartridge is defective. Solution · Replace the toner cartridge. ABCDE ABCDE ABCDE Ghost Images · The Form Type setting in the printer driver is set incorrectly. [. . . ]