User manual LEXMARK E450DN

[. . . ] E450dn User's Guide June 2006 www. lexmark. com Lexmark and Lexmark with diamond design are trademarks of Lexmark International, Inc. , registered in the United States and/or other countries. 740 West New Circle Road Lexington, Kentucky 40550 Edition: June 2006 The following paragraph does not apply to any country where such provisions are inconsistent with local law: LEXMARK INTERNATIONAL, INC. , PROVIDES THIS PUBLICATION "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some states do not allow disclaimer of express or implied warranties in certain transactions; therefore, this statement may not apply to you. This publication could include technical inaccuracies or typographical errors. [. . . ] Touch something metal, such as the printer frame, before you touch a memory card. Avoid touching the connection points along the edge of the card. 4 5 Align the notches on the bottom of the card with the notches on the connector. Push the memory card firmly into the connector until the latches on either end of the connector snap into place. It may require some force to fully seat the card. 6 7 8 9 Make sure each latch fits over the notch on each end of the card. Close the front door. Adding a flash memory card The system board has two connectors for an optional flash memory card. CAUTION: If you are installing a flash memory card after setting up the printer, turn the printer off, and unplug the power cord from the wall outlet before continuing. Note: Flash memory card options designed for other Lexmark printers may not work with your printer. 1 2 Access the system board (see Accessing the system board on page 30). Warning: Flash memory is easily damaged by static electricity. Touch something metal, such as the printer frame, before you touch a flash memory card. Avoid touching the connection points along the edge of the card. Adding a memory card 33 Installing options 3 Squeeze the retainers, and align the plastic pins on the flash memory card with the holes on the system board. 4 Push the flash memory card firmly into the holes of the system board until it snaps into place. Note: The flash card can be installed in the top or the bottom set of connector pin holes. 5 6 7 8 Close the side access door. Plug the power cord into the wall outlet and turn the printer on to continue print functions. Adding a flash memory card 34 Installing options Installing an optional 550-sheet drawer CAUTION: Turn the printer off, and unplug the power cord from the wall outlet before continuing. Place the printer unit directly on top of the 550-sheet drawer. Recognizing installed options The printer driver should automatically recognize the newly-installed option when the printer is turned on. If it does not, you can add the appropriate option manually. 1 2 3 4 5 Click Start Settings Printers. Select the printer icon. Click File Properties. Click the Install Options tab. Add the appropriate options to your configuration: Memory Card--Increase the printer memory to the appropriate number. 550-sheet drawer 6 Click OK. Installing an optional 550-sheet drawer 35 5 Maintaining the printer Periodically, you need to complete certain tasks to maintain optimum print quality. These tasks are covered in this chapter. If several people are using the printer, you may want to designate a key operator to do the setup and maintenance of your printer. Refer printing problems and maintenance tasks to this key operator. In the U. S. , contact Lexmark at 1-800-539-6275 for information about Lexmark Authorized Supplies Dealers in your area. In other countries or regions, visit the Lexmark Web site at www. lexmark. com, or contact the place where you bought your printer. Storing supplies Choose a cool, clean storage area for your printer supplies. Store supplies right side up in their original packaging until you are ready to use them. Do not expose supplies to: · · · · · · Direct sunlight Temperatures above 35°C (95°F) High humidity (above 80%) Salty air Corrosive gases Heavy dust Determining the status of supplies The printer control panel alerts you once a supply item or maintenance is required. [. . . ] Replacement is not available to you if the product you present for exchange is defaced, altered, in need of a repair not included in warranty service, damaged beyond repair, or if the product is not free of all legal obligations, restrictions, liens, and encumbrances. Before you present this product for warranty service, remove all toner cartridges, programs, data, and removable storage media (unless directed otherwise by Lexmark). For further explanation of your warranty alternatives and the nearest Lexmark authorized servicer in your area contact Lexmark on the World Wide Web at http://support. lexmark. com. Remote technical support is provided for this product throughout its warranty period. [. . . ]