User manual LEXMARK OPTRA C710

[. . . ] First Edition (September 1999) The following paragraph does not apply to any country where such provisions are inconsistent with local law: LEXMARK INTERNATIONAL, INC. PROVIDES THIS PUBLICATION "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some states do not allow disclaimer of express or implied warranties in certain transactions; therefore, this statement may not apply to you. This publication could include technical inaccuracies or typographical errors. [. . . ] Align the rear paper guide with the position for the paper size you are loading. 106 Chapter 6: Loading paper in the trays The position of the rear paper guide tells the printer the size of the paper in the tray. If the rear paper guide is in the wrong position, you may experience paper feeding problems or incorrect formatting of pages. 6 7 8 9 10 Set the rear paper guide into the holes on the side and bottom of the paper tray. Squeeze the snap lock on the end of the side paper guide. Lift the side paper guide from the paper tray. Align the side paper guide with the position for the paper size you are loading. Set the side paper guide into the holes on the side and bottom of the paper tray. 11 Before loading the paper, flex the sheets back and forth to loosen them, and then fan them. Straighten the edges on a level surface. Chapter 6: Loading paper in the trays 107 12 Maximum stack height Load the paper with the recommended print side face up. Do not exceed the maximum stack height indicated on the label inside the paper tray. Place the short edge of the paper at the front of the tray. If you're loading preprinted letterhead, place the top of the page at the front of the tray with the letterhead up. Short edge 13 Slide the paper tray into the printer. 108 Chapter 6: Loading paper in the trays Tray linking If you want to increase your printer's paper capacity, you can add an optional drawer unit with two 250-sheet paper trays to your printer. If you load the same paper size and paper type in more than one tray, the printer automatically links the trays when one tray is empty, and feeds paper from the other tray. By linking the trays and multipurpose feeder, you can effectively create a single paper source that holds up to 800 sheets. To initiate tray linking: 1 2 Load paper of the same size and type in all the trays you want to link. Make sure the rear paper guide is set to the proper position for the paper size you have loaded. The position of the rear paper guide informs the printer of the paper size loaded in the tray. If you want to link the multipurpose feeder to a tray, select the appropriate MP Feeder Size setting from the Paper Size Menu. 3 Select the same Paper Type setting for all sources. See page 22 or refer to the Setup Guide for more information about changing the Paper Type setting. To disable tray linking, change the Paper Type setting for one or more of the trays to a Custom Type setting. See page 22 for more information. Chapter 6: Tray linking 109 Using the multipurpose feeder The multipurpose feeder holds 50 sheets of paper, 30 transparencies, 30 sheets of labels, 9 envelopes or 30 card stock sheets. Refer to the Setup Guide for instructions on loading media in the multipurpose feeder. If you want to use the multipurpose feeder like you use other trays, ensure the MP menu item in the Paper Menu is set to Cassette. Note: Do not close the multipurpose feeder while paper or envelopes are in the feeder. You can also use the multipurpose feeder to manually feed a single sheet or envelope. To load paper in the multipurpose feeder: 1 Pull the front of the multipurpose feeder down. 2 Before loading the media, flex the sheets back and forth to loosen them, and then fan them. Straighten the edges on a level surface. 110 Chapter 6: Using the multipurpose feeder 3 Load the media face down and slide the paper guide to the right until it touches the media. [. . . ] Different symbol sets offer the diverse characters required for different languages or symbol-intense applications. The printer's main circuit board. 252 Glossary T timeout. A time interval allotted for certain operations to occur. A type of network communication that conforms to IEEE 802. 5 standard. [. . . ]