User manual LEXMARK X642E MFP

[. . . ] X642eLaser MFP User's Guide Lexmark and Lexmark with diamond design are trademarks of Lexmark International, Inc. , registered in the United States and/or other countries. 740 West New Circle Road Lexington, Kentucky 40550 May 2006 www. lexmark. com Edition: May 2006 The following paragraph does not apply to any country where such provisions are inconsistent with local law: LEXMARK INTERNATIONAL, INC. , PROVIDES THIS PUBLICATION "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some states do not allow disclaimer of express or implied warranties in certain transactions; therefore, this statement may not apply to you. This publication could include technical inaccuracies or typographical errors. [. . . ] It can be used for single-page or manual printing or as an additional tray. Note: If you install an optional envelope feeder, you can still use the multipurpose feeder. The multipurpose feeder can hold approximately: · · · 100 sheets of 75 g/m2 (20 lb) paper 10 envelopes 75 transparencies The multipurpose feeder accepts print media within the following dimensions: · · Width--69. 85 mm (2. 75 in. ) to 215. 9 mm (8. 5 in. ) Length--127 mm (5 in. ) to 355. 6 mm (14 in. ) The icons on the multipurpose feeder show you how to load the multipurpose feeder with paper, how to turn an envelope for printing, and how to load letterhead paper for simplex and duplex printing. A 83 finisher affects how letterhead documents should be loaded for duplexing. You can print simplex jobs on letterhead (or other preprinted media) that has been loaded specifically for duplex printing by changing the value in the Paper Loading menu. Simplex letterhead Duplex letterhead Envelope To load print media: Note: Do not add or remove print media when the MFP is printing from the multipurpose feeder or when the control panel indicator light is blinking. Doing so may cause a jam. 1 Push the release latch, and lower the multipurpose feeder. 2 Pull the tray extension out. Note: Do not place objects on the multipurpose feeder. Also, avoid pressing down or applying excessive force on it. 3 Slide the width guide to the far right. 84 4 Flex the sheets or envelopes back and forth to loosen them, then fan them. Straighten the edges on a level surface. Note: Hold transparencies by the edges, and avoid touching the print side. Fan the stack of transparencies to prevent jams. Be careful not to scratch or leave fingerprints on the transparencies. Paper Envelopes Transparencies 5 Load the media in the tray. Use the stack height label as a guide for stack height when loading print media. Loading paper, transparencies, or envelopes Note: Letterhead or other preprinted paper must be loaded differently depending on the options you have installed. · · Load paper or transparencies with the left edge of the stack against the stack height label and with the recommended print side facing up. Load envelopes flap side down with the stamp area and flap on the left. The end of the envelope with the stamp area enters the multipurpose feeder first. ­ Never use envelopes with stamps, clasps, snaps, windows, coated linings, or selfstick adhesives. These envelopes may severely damage the MFP. Note: Load only one size and type of print media at a time in the multipurpose feeder. Do not mix sizes and types in the same tray. Loading letterhead or preprinted paper · Follow the illustrations for loading the paper according to your options. 85 · Do not fill paper above the load line. Overfilling the tray may cause jams. Simplex (single sided) Duplex 6 Slide the side guide toward the inside of the tray until it lightly rests against the edge of the media. 7 Set the Paper Size and Paper Type for the multipurpose feeder to the correct value for the print media you loaded. [. . . ] This equipment uses CA11A telephone jacks. 182 Notice to users of the New Zealand telephone network The following are special conditions for the Facsimile User Instructions. The grant of a telepermit for any item of terminal equipment indicates only that Telecom has accepted that the item complies with minimum conditions for connection to its network. It indicates no endorsement of the product by Telecom, nor does it provide any sort of warranty. Above all, it provides no assurance that any item will work correctly in all respects with another item of telepermitted equipment of a different make or model, nor does it imply that any product is compatible with all of Telecom's network services. [. . . ]