User manual LEXMARK X738DTE

[. . . ] Do not place or use this product near water or wet locations. CAUTION--POTENTIAL INJURY: This product uses a laser. Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. This product uses a printing process that heats the print media, and the heat may cause the media to release emissions. [. . . ] · The Off setting filters print jobs using the standard protocol. · The On setting processes raw binary PostScript print jobs. Sets the network address information for an external print server that is attached to the printer using a USB cable Note: This menu item is available only if the printer is attached to an external print server through the USB port. ENA Address <xxx>. <xxx>. <xxx>. <xxx> ENA Netmask <xxx>. <xxx>. <xxx>. <xxx> Sets the netmask information for an external print server that is attached to the printer using a USB cable Note: This menu item is available only if the printer is attached to an external print server through the USB port. ENA gateway <xxx>. <xxx>. <xxx>. <xxx> Sets the gateway information for an external print server that is attached to the printer using a USB cable Note: This menu item is available only if the printer is attached to an external print server through the USB port. Serial <x> menu Menu item PCL SmartSwitch On Off Description Sets the printer to automatically switch to PCL emulation when a print job received through a serial port requires it, regardless of the default printer language Notes: · On is the factory default setting. · When the Off setting is used, the printer does not examine incoming data. · When the Off setting is used, the printer uses PostScript emulation if PS SmartSwitch is set to On. It uses the default printer language specified in the Setup menu if PS SmartSwitch is set to Off. PS SmartSwitch On Off Sets the printer to automatically switch to PS emulation when a print job received through a serial port requires it, regardless of the default printer language Notes: · On is the factory default setting. · When the Off setting is used, the printer does not examine incoming data. · When the Off setting is used, the printer uses PCL emulation if PCL SmartSwitch is set to On. It uses the default printer language specified in the Setup menu if PCL SmartSwitch is set to Off. Understanding printer menus 171 Menu item NPA Mode On Off Auto Description Sets the printer to perform the special processing required for bidirectional communication following the conventions defined by the NPA protocol Notes: · Auto is the factory default setting. · When the On setting is used, the printer performs NPA processing. If the data is not in NPA format, it is rejected as bad data. · When the Off setting is used, the printer does not perform NPA processing. · When the Auto setting is used, the printer examines data, determines the format, and then processes it appropriately. · Changing this setting from the control panel and then exiting the menus causes the printer to restart. Serial Buffer Disabled Auto 3k to <maximum size allowed> Sets the size of the serial input buffer Notes: · Auto is the factory default setting. · The Disabled setting turns off job buffering. Any jobs already buffered on the disk are printed before normal processing is resumed. · The serial buffer size setting can be changed in 1k increments. · The maximum size allowed depends on the amount of memory in the printer, the size of the other link buffers, and whether Resource Save is set to On or Off. · To increase the maximum size range for the Serial Buffer, disable or reduce the size of the parallel, serial, and network buffers. · Changing this setting from the control panel and then exiting the menus causes the printer to restart. Job Buffering Off On Auto Temporarily stores jobs on the printer hard disk before printing Notes: · · · · Off is the factory default setting. The Off setting does not buffer print jobs to the hard disk. The On setting buffers jobs on the printer hard disk. The Auto setting buffers print jobs only if the printer is busy processing data from another input port. The menu selection is updated. · Changing this setting from the control panel and then exiting the menus causes Serial Protocol DTR DTR/DSR XON/XOFF XON/XOFF/DTR XONXOFF/DTRDSR Selects the hardware and software handshaking settings for the serial port Notes: · · · · DTR is the factory default setting. DTR/DSR is a hardware handshaking setting. [. . . ] The UN Convention on Contracts for the International Sale of Goods shall not apply. 14 UNITED STATES GOVERNMENT RESTRICTED RIGHTS. The Software Program has been developed entirely at private expense. Rights of the United States Government to use the Software Program are as set forth in this Software License Agreement and as restricted in DFARS 252. 227-7014 and in similar FAR provisions (or any equivalent agency regulation or contract clause). 15 CONSENT TO USE OF DATA. You agree that Lexmark, its affiliates, and agents may collect and use information you provide in relation to support services performed with respect to the Software Program and requested by you. [. . . ]