User manual LG -CB773F-EJ-

[. . . ] To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only. On transportation When you carry the display unit, hold the unit itself, not the speakers. If you fail to do so, the speakers may come out of the unit and the unit may fall. This can cause injury. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. [. . . ] DHCP: Automatic configuration to set an IP address. Manual: Manual configuration to set an IP address. For details, see "Setting an IP Address and communication speed" on page 39 (GB). Model Name: Serial Number: Operation Time: Software Version: IP Address: Speed Setup Sets a communication speed between the display unit and an optional adaptor with communication function such as BKM-FW32 or BKM-FW50. For details, see "Setting an IP Address and communication speed" on page 39 (GB). Select Set ENTER Exit TIMER/CLOCK menu MENU Note "IP Address" appears on the menu only when an option adaptor with a communication function such as BKM-FW32 or BKM-FW50 is installed into the OPTION1 slot. Serial Number Indicates the serial number. You can set the timer, adjust time, display the built-in clock, or make the unit power on/off at a predetermined time. TIMER/CLOCK Clock Set Clock Display: On/Off Timer Off Select Set ENTER Exit MENU Note Operation Time Indicates the total number of hours of operation. Note The time and the day are not preset in the factory setting. Clock Set Sets the time and the day. For details, see "Adjusting the time and the day" on page 37 (GB). Time spent in standby mode is not counted as part of the Operation Time. Software Version Indicates the system software version. All Reset Resets all the adjustments and setting values to the factory preset. Note Clock Display Displays the currently set time on the screen when set to On. For details, see "Displaying the time" on page 37 (GB). The Index Number will not be reset. On/Off Timer Sets the time at which the power is automatically turned on or off. For details, see "On/Off Timer Function" on page 38 (GB). 20 (GB) Watching the Picture Watching the Picture Before you start · Power on the display. · Power on the connected equipment and play a video source. · To display the input signal information and Picture Mode on the screen when turning on the power or switching the input signal, set "Display" in the Custom Setup menu to On. · To select the language of the menus, see "Selecting the On-screen Language" on page 36 (GB). Press INPUT1, INPUT2, OPTION1 or OPTION2 button on the Remote Commander to switch the input signal. When multiple formats of signals can be input to the selected input connector, the indication changes every time you press the corresponding button. For example, every time you press the INPUT2 button, the indication switches to "Input2 RGB" or "Input2 Component" alternately. The signal mode of Option 1 or 2 slot is set to S VIDEO. The signal mode of Option 1 or 2 slot is set to analog RGB. The signal mode of Option 1 or 2 slot is set to component video. 23 (GB) Selecting Image Quality / Adjusting the Picture Selecting Image Quality You can set an image quality suitable for the type of picture or the brightness of the location where the unit is installed. Adjusting the Picture While watching the picture, you can adjust contrast, brightness, chroma, phase, and so on, to suit your taste. The adjustments can be carried out for each input signal separately. You can also store the adjusted levels in memory. Set the Picture Mode to any of "User1" to "User3. " 1 Press MENU. The main menu appears on the screen. PICTURE/SOUND CONTROL Picture Mode: Adjust Picture Adjust Sound Vivid Adjusting the Contrast, Brightness, Chroma, and Phase, etc. Press MENU to show the main menu and adjust "Backlight, " "Contrast, " "Brightness, " "Chroma, " "Phase, " "Sharpness, " "Noise Reduct. , " "Cinema Drive, " "Dynamic Picture, " "Color Temp. , " "Color Correct. " or "Gamma Correct. " on the Adjust Picture menu. Select Set ENTER Exit MENU 2 Press M/m to move the cursor (yellow) to "PICTURE/SOUND CONTROL" and press ENTER. The PICTURE/SOUND CONTROL menu appears on the screen. PICTURE/SOUND CONTROL Picture Mode: Adjust Picture Adjust Sound Vivid Backlight Select "Backlight" with M/m and press ENTER. Adjust the brightness of the background with M/m/ </, within the range of MIN (0) to MAX (100), then press ENTER. M/, : to increase the brightness of the background m/<: to decrease the brightness of the background While showing two pictures, both pictures will be adjusted. Select Set ENTER Exit MENU 3 Press M/m to move the cursor (yellow) to "Picture Mode" and press ENTER. The following menu appears on the screen. PICTURE/SOUND CONTROL Picture Mode: Adjust Picture Adjust Sound Vivid Standard User1 User2 User3 Contrast Select "Contrast" with M/m and press ENTER. [. . . ] This function shows the display's condition based on the pattern shown by the flashing of the POWER/ STANDBY indicator. The flashing pattern informs you of the display's current condition. If the POWER/STANDBY indicator flashes, check the number of flashes and contact your authorized Sony dealer. In the INITIAL SETUP/INFORMATION menu, select "Speed Setup" with M/m and press ENTER. INITIAL SETUP/INFORMATION Speed Setup Speed: Execute Auto Detect Select Set ENTER Exit MENU 2 Press ENTER and select a communication speed with M/m, then press ENTER. Select "Auto Detect" when you want to set an appropriate communication speed for your network configuration automatically. INITIAL SETUP/INFORMATION Speed Setup Speed: Execute Auto Detect 10Mbps/Half Dup 10Mbps/Full Dup 100Mbps/Half Dup 100Mbps/Full Dup 1 Check the flashing pattern of the POWER/ STANDBY indicator. [. . . ]