User manual LG 15LS1R

[. . . ] This information shall be given in a language acceptable to the country where the apparatus is intended to be used. The important safety instructions shall be entitled "Important Safety Instructions". The following safety instructions shall be included where applicable, and, when used, shall be verbatim as follows. Additional safety information may be included by adding statements after the end of the following safety instruction list. [. . . ] How to use I 2 Turn on the PC and the TV. Select R G B input source by using the I N P U T button on the remote control. I Supported Display Specifications RGB-PC mode Resolution 640x480 800x600 1024x768 RGB-DTV mode Resolution 720x480i 720x480p 720x576i 720x576p 1280x720p Horizontal Frequency(KHz) 15. 734 31. 469 15. 625 31. 25 37 . 50 44. 955 45. 00 Vertical Frequency(Hz) 59. 939 59. 94 50. 00 50. 00 50. 00 59. 94 60. 00 G G G RGB OUTPUT AUDIO Horizontal Frequency(KHz) 31. 469 37 . 879 35. 156 48. 363 Vertical Frequency(Hz) 59. 94 60. 31 56. 25 60. 00 !NOTES G To get the the best picture quality, adjust the PC graphics card to 1024x768, 60Hz. Using other formats (VGA, SVGA, etc. ) or refresh rates may result in reduced picture quality. (To change the computer video output format, please refer to the operating manual for the computer you are using). Avoid keeping a fixed image on the screen for a long period of time. The fixed image may become permanently imprinted on the screen. If the message "No signal" appears on the screen, adjust the PC output to a format listed in the `Supported Display Specifications'. The synchronization input form for Horizontal and Vertical frequencies is separate. G 20 SCREEN SETUP (15 inches only) TV POWER INPUT Auto Configure Automatically adjusts picture position and minimizes image shaking. Although the image is still not correct, your set is functioning properly but needs further adjustment. This function works in the following mode: RGB-PC mode. MTS A. PROG MEMORY/ERASE CAPTION 1 4 7 2 5 8 0 3 6 9 EXTERNAL EQUIPMENT SETUP MUTE FCR CH 1 Press the A . G p. 47 APC Selects the factory preset picture depend on the viewing environment. G p. 33 DASP Selects the factory preset sound for type of program. G p. 38 ARC/ MENU CH REVIEW SLEEP APC DASP ARC/ * * Not functional POWER Turns your TV or any other programmed equipment on or off, depending on the mode. TV In AV, Component, and RGB input sources, screen returns to the last TV channel. WATCHING TV / CHANNEL CONTROL INPUT Select the desired input source: TV, AV, Component, and RGB. NUMBER button MUTE Switch the sound on or off. G p. 26 FCR Scroll through the programmed Favorite channels. G p. 31 Installing Batteries Remote control effective range TV POWER INPUT MTS A. PROG MEMORY/ERASE CAPTION 1 2 5 8 0 3 6 9 I Open the battery compartment cover on the back side and install the batteries matching correct polarity (+ with +, - with -). Don't mix old or used batteries with new ones. Close cover. 4 7 MUTE FCR I I Use a remote control up to 7 meters distance and 30 degree (left/right) within the receiving unit scope. Dispose of used batteries in a recycle bin to preserve environment. I I 25 WATCHING TV / CHANNEL CONTROL TURNING ON TV TV MTS POWER INPUT A. PROG MEMORY/ERASE CAPTION 1 First, connect power cord correctly. At this moment, the TV switches to standby mode. [. . . ] I To cancel the O n / O f f t i m e r function, select O f f. 7 Press the E N T E R button to save. 46 SLEEP TIMER SETTING The Sleep Timer turns the TV off at the preset time. Note that this setting is cleared when the TV is turned off. VOL ENTER VOL CH MENU REVIEW SLEEP APC DASP ARC/ * 1 Press the S L E E P button repeatedly to select the number of minutes. First the ` - - - ' option appears on the screen, followed by the following sleep timer options : 10, 20, 30, 60, 90, 120, 180, and 240 minutes. TIME SETTING 2 When the number of minutes you want is displayed on the screen, press the E N T E R button. The timer begins to count down from the number of minutes selected. 3 To check the remaining minutes before the TV turns off, press the S L E E P button once. 4 To cancel the Sleep Timer, press the S L E E P button repeatedly to select ` - - - '. 47 TIME SETTING AUTO SHUT-OFF SETTING If set to on and there is no input signal, the TV turns off automatically after 10 minutes. 0 MUTE FCR CH VOL ENTER VOL CH MENU REVIEW SLEEP APC DASP ARC/ * Timer 1 Press the M E N U button and then use D or E button to select the T i m e r menu. Clock Off timer On timer Auto off 2 Press the G button and then use D or E button to select A u t o o f f. Timer Clock DE FG MENU 1 48 TIME SETTING 3 Press the G button and then use D or E button to select O n or O f f. Off timer On timer Auto off G On Off DE FG MENU 4 Press the E N T E R button to save. 2 3 APPENDIX TROUBLESHOOTING The operation does not work normally. I The remote control doesn't work Check to see if there is any object between the product and the remote control causing obstruction. [. . . ]