User manual LG 23EN43VQ-B

[. . . ] : Warning and Caution are to call the userʼs attention to the possible danger. Read and follow them carefully in order to prevent a safety accident. : Warning and Caution are indicated in this guide and the product itself to help protect the users from danger. WARNING n Installation Be sure to request to the service center or installation specialty store when installing products. • It will cause fire or electric shock or explosion or injury. Request to the service center or installation specialty store when reinstalling the installed product. • It will cause fire or electric shock or explosion or injury. Do not disassemble, fix, and modify products randomly. • It will cause fire or electric shock. n In-use Do not place flammable stuffs close to the product. • It will cause fire. Do not allow water to run into the product. • It will cause electric shock or breakdown. Do not give the shock to the product. • It will cause breakdown when giving the shock to the product. Request to the service center or installation specialty store when the product becomes wet. • It will cause fire or electric shock. Do not give the shock using sharp and pointed objects. • It will cause breakdown by damaging parts. CAUTION n In-use Do not clean using the powerful detergent like solvent but use soft cloths. • It will cause fire or product deformation. Do not press the screen using powerful pressure or select two buttons. • It will cause product breakdown or malfunction. Do not touch or pull the lead wire with wet hands. • It will cause product breakdown or electric shock. Ownerʼs & Installation Manual 3 Part Description Part Description Simple Wired Remote Controller 1. Operation Mode select Button 2 3 FAN SPEED TEMP OPER MODE 4 5 Each function will be shown on the display panel for three seconds or so when the power is applied at first. Accessory Connecting Cable (1EA) Fixing Screw (2EA) Owner / Installation Manual 4 Wired Remote Controller Installation instruction ENGLISH Installation instruction 1. [. . . ] - If any button is inputted during the test run mode, the test run mode will be forced to be relreased. • What is the test run mode??- This means the operation of the product under the cooling, strong wind, and Comp on state without performing room temperature control in order to confirm the installed state during the product installation. Ownerʼs & Installation Manual 9 Installation instruction Installer Setting - Setting Address of Central Control It's the function to use for connecting central control. Please refer to central controller manual for the details button 1 When pressing the for moreand 3 button simultaneously than OPER MODE seconds, the system will be entered into the installer setting mode. - After entering into the installer setting mode, select the central control address setting code value by pressing the button. * Setting address of central control code value : 02 OPER MODE up the group nember and indoor unit with 2 Set temperature adjustment(▲, ▼) buttons. the FAN SPEED TEMP Group number Indoor unit number OPER MODE TEMP For example, when setting as [ Group number=2 Indoor number=3 ] it will be displayed as shown in the left figure. button, the 3 When pressing thethe address valuesystem will be set up with which has been established at present. button and 4 When pressing the for more than 3 button simultaneously OPER MODE seconds after the setting has been completed, the setting mode will be released. - If there isn’t any button input for more than 25 seconds, the installer setting mode will also be released. • If you connect the indoor unit to the central controller, you should set the network address of the indoor unit so that the central controller could recognize it. Ownerʼs & Installation Manual 11 Installation instruction Installer Setting -Thermistor This is the function to select the temperature sensor to judge the room temperature. button 1 When pressing the for moreand 3 button simultaneously than OPER MODE seconds, the system will be entered into the installer setting mode. - After entering into the installer setting mode, select the thermistor sensor setting code value by pressing the button. will begin if you press the set the 2 Press the temperature button andthan the desired room temperature lower current room temperature. A click of the button will increase the desired temperature by 1°C or 2°F. A click of the button will decrease the desired temperature by 1°C or 2°F. TEMP FAN SPEED TEMP OPER MODE - Setting temp range : 18°C~30°C (64°F~86°F) - If the desired temperature is set higher than the current room temperature, the cooling function will not begin and just the blowing operation will continue. 3 If you prees the mode button during the operation, the operation mode will be changed in the order of cooling, dry(dehumidification), heating, auto-operation and fan operation. If the product is a cooling-only model, the operation mode will be changed in the order of cooling, dry(dehumidification), auto-operation and fan operation. 4 If you press the operation will stop. button, the cooling Ownerʼs & Installation Manual 17 Owner's instruction Standard Operation - Heating Mode It supplies warm wind to the indoor want 1 If you the to set the heating operation, press button. And press the button. OPER MODE 2 Set the desired room temperature higher than the current room temperature. TEMP A click of the button will increase the desired temperature by 1°C or 2°F. A click of the button will decrease the desired temperature by 1°C or 2°F. FAN SPEED TEMP OPER MODE - Setting temp range : 16°C~30°C (60°F~86°F) - If the desired temperature is set lower than the current room temperature, the heating function will not begin. 3 If you prees the mode button during the operation, the operation mode will be changed in the order of cooling, dry(dehumidification), heating, auto-operation and fan operation. 4 If you press the operation will stop. What is the three-minute delay function? button, the cooling It will take time for the product to blow warm air. The room will be heated with warm air after three minutes when the compressor begins operation. n The cooling-only model will not do heating function. 18 Wired Remote Controller Owner's instruction ENGLISH Standard Operation - Auto Operation Mode by 1 After operating the productautopressing the button, set up the operation by pressing the OPER MODE button. Over 2 “Auto Change the setMode” – Heat pump model only When desired temperature is higher than the room temperature during the auto operation => Heating operation [For Heat pump models only] When desired the set temperature is lower than the room temperature during the auto operation => Cooling operation - Setting temp range : 18°C~30°C (64°F~86°F) OPER MODE FAN SPEED TEMP 3 “Auto Operation Mode” exclusive purpose For the products with the of cooling only, “AI” is indicated at the temperature display section. When cold When cool When appropriate When warm When hot Ownerʼs & Installation Manual 19 Owner's instruction Standard Operation - Dehumidification Mode It removes humidity while air-cooling weakly. by 1 After operating the productdry pressing the button, set up the (Dehumidification) by pressing the button. OPER MODE operation selected, “dh” will 2 When the drythe displayiswindow as shown be shown on on the left side. - The temperature setting can not be adjusted during operation this mode. FAN SPEED TEMP OPER MODE 3 Press the button to select airflow rate [SLo→Lo→Med→Hi→Po]. - The initial wind powerfulness of humidity removal drive is ‘weak’. FAN SPEED • In rainy season or high humidity climate, it is possible to operate simultaneously dehumidifier and cooling mode to remove humidity effectively. • The menu item of wind powerfulness might not be partially selected according to the product. 20 Wired Remote Controller Owner's instruction ENGLISH Standard Operation - Fan Mode It blows the air as it is in the indoor, not the cold wind. by pressing 1 After operating the productfan operation by the button, set up the pressing the OPER MODE button. operation selected, “Fn” will 2 When the drythe displayiswindow as shown be shown on on the left side. - The temperature setting can not be adjusted during operation this mode. FAN SPEED TEMP OPER MODE 3 Press the button to select airflow rate [SLo→Lo→Med→Hi→Po]. When running ventilation, compressor of AHU doesn’t work. FAN SPEED • Ventilation drive does not release cool wind but general fan • Because it releases the wind that has no temperature difference from the room, it functions to circulate the inside air. • The menu item of wind powerfulness might not be partially selected according to the product. Ownerʼs & Installation Manual 21 Owner's instruction Function Setting - Fan Speed Selection It blows the air as it is in the indoor, not the cold wind. speed which you want 1 Select the proper fanbutton on the remote by pressing the controller. - If you press the button, the fan speed will change in the order of [SLo→Lo→Med→ Hi→Po]. [. . . ] vane angle 3 Select the by pressing number from ‘vane1’ to ‘vane4’ the button. OPER MODE OPER MODE FAN SPEED TEMP OPER MODE - When selecting the vane number, the vane which is corresponded to the number will be opened and closed. vane angle from 4 Select theup/down button. ‘P0’ to ‘P6’ with the temp - In the case of the wind flowing out angle, (Minimum angle)……………. (Max angle) ‘ P0 < P1 < P2 < P3 < P4 < P5 < P6 ’ 5 When pressing the button for 3 seconds, the setting is finished and the vane angle control setting is completed. - If there isn’t any button input for approx. [. . . ]