User manual LG 23LX1R-MA

[. . . ] Number of pages : 28 N O T E S "This part contain Eco-hazardous substances (Pb, Cd, Hg, Cr6+, PBB, PBDE, etc. ) within LG standard level, Details should be followed Eco-SCM management standard[LG(56)-A-2524]. Especially, Part should be followed and controlled the following specification. (1)Eco-hazardous substances test report should be submitted when Part certification test and First Mass Production. (2) Especially, Don't use or contain lead(Pb) and cadmium(Cd) in ink. 3. Special Instructions * LGENT : Printed in China * LGENP : Printed in China * LGEIL : Printed in India * LGEDI : Printed in Indonesia * LGEIN : Printed in Indonesia * LGEMA : Printed in Poland * LGETH : Printed in Thailand * LGEWA : Printed in U. K. [. . . ] THUMBSTICK Navigate the on-screen menus and adjust the system set(Up/Down/Left tings to your preference. Right/ENTER) Installing Batteries Remote control effective range I Open the battery compartment cover on the back side and install the batteries matching correct polarity (+ with +, - with -). Don't mix old or used batteries with new ones. I Close cover. I Use a remote control up to 7 meters distance and 30 degree (left/right) within the receiving unit scope. Dispose of used batteries in a recycle bin to preserve environment. I POWER TV SAP PICTURE INPUT SOUND TIMER 1 4 7 - 2 5 8 0 3 6 9 FAV 9 MFL34797029-en DRRT 10/30/07 5:05 PM Page 10 PREPARATION STAND INSTALLATION I Here shown may be somewhat different from your TV. Carefully place the product screen side down on a cushioned surface that will protect product and screen from damage. 1 10 PREPARATION 2 Hold the H I N G E B O D Y and bend it upward. HINGE BODY 3 Insert the S T A N D B O D Y into the product until clicking sound. STAND BODY Assemble the parts of the S T A N D B O D Y with C O V E R B A S E of the product. 4 COVER BASE MFL34797029-en DRRT 10/30/07 5:05 PM Page 11 DETACHING STAND I Here shown may be somewhat different from your TV. Carefully place the product screen side down on a cushioned surface that will protect product and screen from damage. 1 2 Pull cover base backward while pressing button on stand body. PREPARATION 3 Shake the base while pulling, it will separate from stand body. 4 Hold the H I N G E B O D Y and bend it upward. HINGE BODY 5 Pull stand body to separate from set while pressing the 2 latches. 11 MFL34797029-en DRRT 10/30/07 5:05 PM Page 12 PREPARATION BACK COVER FOR WIRE ARRANGEMENT I Here shown may be somewhat different from your TV. To connect an additional equipment, see the E X T E R N A L E Q U I P M E N T S E T U P section. 12 PREPARATION 1 2 Install the C A B L E M A N A G E M E N T as shown. CABLE MANAGEMENT How to remove the CABLE MANAGEMENT First, press the cable management. Hold the C A B L E M A N A G E M E N T with both hands and pull it upward. !NOTE Do not hold the C A B L E M A N A G E M E N T when moving the product. (Refer to the owner's manual for the digital set-top box. operation) Select C o m p o n e n t input source by using the I N P U T button on the remote control. H/P AUDIO VIDEO COMPONENT IN I Y, CB/PB, CR/PR Signal 480i 480p 720p 1080i 1080p Component Yes Yes Yes Yes Yes HDMI No Yes Yes Yes Yes Resolution 720x480i 720x480p 1280x720p 1920x1080i Horizontal Frequency(KHz) 15. 73 15. 73 31. 47 31. 50 44. 96 45. 00 33. 72 33. 75 27 . 00 33. 75 67 . 43 67 . 50 Vertical Frequency(Hz) 59. 94 60. 00 59. 94 60. 00 59. 94 60. 00 59. 94 60. 00 24. 00 30. 00 59. 94 60. 00 1920x1080p 17 MFL34797029-en DRRT 10/30/07 5:05 PM Page 18 EXTERNAL EQUIPMENT SETUP DVD SETUP When connecting Component cable 1. How to connect EXTERNAL EQUIPMENT SETUP Connect the video outputs (Y, PB, PR) of the DVD to the C O M P O N E N T I N V I D E O jacks on the set. Match the jack colors (Y = green, PB = blue, and PR = red). Connect the audio outputs of the DVD to the C O M P O N E N T I N A U D I O jacks on the set. AV IN VIDEO AUDIO 1 Y PB PR L R 2 1 ANTENNA/ 2 CABLE IN 2. How to use I S-VIDEO RGB (PC) IN AUDIO (RGB/DVI) IN Turn on the DVD player, insert a DVD. Select C o m p o n e n t input source by using the I N P U T button on the remote control. Refer to the DVD player's manual for operating instructions. L(MONO) R I H/P AUDIO VIDEO COMPONENT IN I 18 MFL34797029-en DRRT 10/30/07 5:05 PM Page 19 VCR SETUP When connecting with a RCA cable 1. How to connect 1 V Connect the A U D I O/V I D E O jacks between TV and VCR. Match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red) HDMI/DVI IN ANT CA AV IN VIDEO SERVICE ONLY L(MONO) R AUDIO S-VIDEO EXTERNAL EQUIPMENT SETUP H/P RS-232C IN (SERVICE ONLY) VIDEO COMPO 2. How to use I 1 Insert a video tape into the VCR and press PLAY on the VCR. [. . . ] Selecting canadian english language rating system. Selecting canadian french language rating system. This function may become available in the future and will be available only for digital channel signal. I I For Canada Lock System Set Password TV Rating-English TV Rating-French Downloadable Rating : Off I I I MFL34797029-en DRRT 10/30/07 5:06 PM Page 25 APPENDIX TROUBLESHOOTING The operation does not work normally. I The remote control doesn't work Check to see if there is any object between the product and the remote control causing obstruction. Ensure you are pointing the remote control directly at the TV. [. . . ]