User manual LG 26LG3DCH

[. . . ] LCD TV OWNER'S MANUAL 22LG3DCH 26LG3DCH 32LG3DCH 32LG3DC Please read this manual carefully before operating your set. Record model number and serial number of the set. See the label attached on the back cover and quote this information to your dealer when you require service. ENERGY STAR is a set of power-saving guidelines issued by the U. S. Environmental Protection Agency (EPA). As an ENERGY STAR Partner LG Electronics USA, Inc. [. . . ] How to use I I Set VCR output switch to 3 or 4 and then tune TV to the same channel number. Insert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owner's manual. ) Antenna ( ) Composite (RCA) Connection AV IN AV IN11 S-VIDEO 1. How to connect 1 V Connect the A U D I O/V I D E O jacks between TV and VCR. Match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red) AUDIO ( MONO ) VIDEO RGB IN (P ANTENNA IN M. P. I. COMPONENT IN VIDEO 1 AUDIO AUDIO (RGB/ EXTERNAL EQUIPMENT SETUP 2. How to use I Insert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owner's manual. ) Select the A V 1 input source on the TV using the I N P U T button on the remote control. I If connected to A V I N 2, select A V 2 input source on the TV (Except 22LG3DCH). I ANT OUT R L VIDEO S-VIDEO !NOTE G If you have a mono VCR, connect the audio cable from the VCR to the A U D I O L ( M O N O ) jack of the TV. ANT IN OUTPUT SWITCH 1. How to connect 1 2 Connect the S - V I D E O output of the VCR to the S - V I D E O input on the TV. Connect the audio outputs of the VCR to the A U D I O input jacks on the TV. COMPONENT IN AV IN 1 AV S-VIDEO S-Video Connection (Except 22LG3DCH) AUDIO ( MONO ) VIDEO R 1 VIDEO 2 AUDIO 2. How to use S-VIDEO VIDEO L R ANT OUT Insert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owner's manual. ) I Select the A V 1 input source on the TV using the I N P U T button on the remote control. I OUTPUT SWITCH ANT IN CAUTION !NOTE G G S-Video provides better quality than composite. Use it when available. Do not connect to both Video and S-Video at the same time. In the event that you connect both Video and the S-Video cables, only the S-Video will work. 23 EXTERNAL EQUIPMENT SETUP OTHER A/V SOURCE SETUP 1. How to connect 1 EXTERNAL EQUIPMENT SETUP V Connect the A U D I O/V I D E O jacks between TV and external equipment. (Video = yellow, Audio Left = white, and Audio Right = red) Camcorder Video Game Set VIDEO L R 2. How to use H/P I VIDEO L/MONO AUDIO R I I Select the A V 2 input source on the TV using the I N P U T button on the remote control. If connected to A V I N 1 input, select the A V 1 input source on the TV. Operate the corresponding external equipment. R 1 AV IN 2 24 PILLOW SPEAKER SETUP I (Except 32LG3DC) Connect a pillow speaker to the LCD TV/Monitor. 1. How to connect 1 2 3 I Connect the P I L L O W S P E A K E R output jack on the back of the TV. [. . . ] I Test the wall power outlet, plug another product's power cord into the outlet where the product's power cord was plugged in. I I I No picture &No sound Picture appears slowly after switching on This is normal, the image is muted during the product startup process. Please contact your service center, if the picture has not appeared after five minutes. No or poor color or poor picture Adjust Color in menu option. I Try unplugging any others electronics that are near by to see if interference is causing the problem. I Are the video cables installed properly? [. . . ]