User manual LG 32170

[. . . ] CAUTION/WARNING SYMBOLS USED WARNING WARNING Indicates that a danger of death or serious injury exists. Indicates that a risk of personal injury or material damage exists. CAUTION OTHER SYMBOLS USED NOTE Explains terms to help users understand how use the product properly. 2_ Safety information Safety information IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic precautions should be observed, including the following: READ ALL INSTRUCTIONS BEFORE USING YOUR ROBOTIC VACUUM CLEANER. Unplug from outlet when not in use and before conducting maintenance. WARNING: to reduce the risk of fire, electric shock, or injury: GENERAL · · · · · · Use only as described in this manual. Do not operate the robotic vacuum cleaner or charger if it has been damaged in any way. If the cleaner is not working as it should, has been dropped, damaged, left outdoors, or dropped in water, return it to a customer care center. [. . . ] - When charging is complete, the battery level indicator and "FULL" will be displayed in the display panel. Flash Power Lamp Charging Lamp Charging <Charge display> Fully charged When the battery level display flashes while cleaning, the robotic vacuum cleaner stops vacuuming and automatically charges itself at the charger. Charge complete Charging Required charging Flash When the battery level flashes and "LO" is displayed while cleaning, robotic vacuum cleaner cannot be operated by the remote control or the buttons on the main unit. In this case, directly carry the robotic vacuum cleaner to the charger to charge the battery. (This is when the battery is completely discharged. ) NOTE When the product is initially purchased, it will take about 120 minutes to fully charge the battery and will run for about 90 minutes. When charging the battery while the battery is over-heated, the charging time can increase. Measures to take when charging is not smooth. When the robotic vacuum cleaner cannot be automatically charged, check the following: - Turn the Power Switch at the bottom of the robotic vacuum cleaner off and on (Reset). - Re-plug the power of the charger (Reset). - Check whether there are any foreign substances on the charge connector and wipe the charge connector on the main unit and the charger with a dry cloth. - Check whether there are objects near the charger that are strong reflectors. When separating the robotic vacuum cleaner from the charger, it will discharge naturally. - Charge the robotic vacuum cleaner through the charger, if possible. a. m. 1 Enter the current "hour". Decrease Increase Decrease Increas Blinks a. m. a. m. Decrease Increase 2 Enter setup mode. Blinks a. m. 3 Set the "hour". Decrease Increase Decrease Increas a. m. a. m. Blinks Decrease Increase 4 Enter the current "minutes". a. m. a. m. 5 Finish the setting. - Press the ( ) button instead of the Time Set button while setting the time to exit Time a. m. - When a Scheduled Cleaning is set, you cannot change the time setting. a. m. a. m. a. m. 24_ Operating the cleaner Operating the cleaner INSTALLING THE ROBOTIC VACUUM CLEANER INSTALLING THE VIRTUAL GUARD You can confine the robotic vacuum cleaner to a particular section by using Fence (virtual wall) mode or clean several sections one by one using Guard (virtual door) mode. Mode Lamp Distance Detection Sensor Main Unit Detection Sensor Mode/Power Button Distance Control Switch Fence/Guard/Off 03 OPERATING THE CLEANER Distance 2 Button operations 1. Mode lamp operations - Fence (virtual wall) Mode: The red lamp flashes. - Guard (virtual door) Mode: The green lamp flashes. Setting the mode - Whenever you press the Mode/Power button, Fence (virtual wall) mode Guard (virtual door) mode Power off is selected in this sequence. Setting the Fence length - Set the distance to restrict the access of robotic vacuum cleaner from the VIRTUAL GUARD using the distance control switch. Switch Setting Max About 1~2m About 2~3m About 3~4m · (Short) ·· (Medium) ··· (Long) 3 Distance Detection Sensor The distance detection sensor forms a virtual straight barrier of the specified fence length. Set the switch according to the required fence length. Forming a Fence (virtual wall) VIRTUAL GUARD creates an invisible barrier that the robotic vacuum cleaner cannot cross. [. . . ] on the suction inlet. · Check whether the filter is · Clean the filter well. cleaner, and manually dock the robotic vacuum onto the charger to charge it. · Replace the batteries in the remote control. (AAA type) clogged. Troubleshooting _43 Troubleshooting CHECkLIST BEFORE SVC CALLS SYMPTOM Robotic vacuum cleaner cannot find the charger. CHECkLIST · Check whether the power MEASURE TO TAkE plug of the charger is plugged correctly into the outlet. [. . . ]