User manual LG 32LC7DC-UK

[. . . ] LCD TV PLASMA TV OWNER'S MANUAL LCD TV MODELS 32LC7D 32LC7DC 37LC7D 42LC7D PLASMA TV MODELS 42PC5D 42PC5DC 50PC5D 50PC5DC Please read this manual carefully before operating your set. Record model number and serial number of the set. See the label attached on the back cover and quote this information to your dealer when you require service. ENERGY STAR is a set of power-saving guidelines issued by the U. S. Environmental Protection Agency(EPA). As an ENERGY STAR Partner LGE U. [. . . ] How to Connect I Connect your wired remote control to the Remote Control port on the TV. 2. Remote Control IR Codes I Output waveform Single pulse, modulated with 37 . 917KHz signal at 455KHz Tc Carrier frequency FCAR = 1/TC = fOSC/12 Duty ratio = T1/TC = 1/3 T1 I Configuration of frame 1st frame Lead code Low custom code High custom code Data code Data code C0 C1 C2 C3 C4 C5 C6 C7 C0 C1 C2 C3 C4 C5 C6 C7 D0 D1 D2 D3 D4 D5 D6 D7 D0 D1 D2 D3 D4 D5 D6 D7 Repeat frame Repeat code Tf I Lead code 9 ms 4. 5 ms APPENDIX I Repeat code 0. 55 ms 9 ms 2. 25 ms I Bit description Bit "0" 0. 56 ms 1. 12 ms Bit "1" 0. 56 ms 2. 24 ms I Frame interval: Tf The waveform is transmitted as long as a key is depressed. Tf Tf Tf=108ms @455KHz 87 APPENDIX (Hexa) 0F 0B 08 79 0E 10-19 4C 1A 09 02 03 00 01 1E 7E 39 40 41 07 06 44 43 52 4D Code Function TV INPUT INPUT POWER RATIO TIMER Number Key 0-9 - (Dash) BACK MUTE VOL D VOL E CH D CH E FAV SIMPLINK CC D E F G Note Remote control Button Remote control Button Remote control Button (Power On/Off) Remote control Button Remote control Button Remote control Button Remote control Button Remote control Button Remote control Button Remote control Button Remote control Button Remote control Button Remote control Button Remote control Button Remote control Button Remote control Button Remote control Button Remote control Button Remote control Button Remote control Button Remote control Button Remote control Button Remote control Button Remote control Button Remote control Button Remote control Button Remote control Button Remote control Button Remote control Button Discrete IR Code (TV Input Selection) Discrete IR Code (Only Power On) Discrete IR Code (Only Power Off) Discrete IR Code (AV1 Input Selection) Discrete IR Code (AV2 Input Selection) (Hexa) BF D4 D5 CE CC 76 77 AF Code Function COMPONENT1 COMPONENT2 RGB-PC HDMI1 HDMI2 Ratio 4:3 Ratio 16:9 Ratio Zoom Note Discrete IR Code (Component1 Input Selection) Discrete IR Code (Component2 Input Selection) Discrete IR Code (RGB-PC Input Selection) Discrete IR Code (HDMI1 Input Selection) Discrete IR Code (HDMI2 Input Selection) Discrete IR Code (Only 4:3 Mode) Discrete IR Code (Only 16:9 Mode) Discrete IR Code (Only Zoom1 Mode) ENTER MENU SOUND PICTURE EXIT SAP ADJUST BRIGHT BRIGHT + TV POWER ON POWER OFF AV1 AV2 88 APPENDIX 5B 0A CB E1 E0 D6 C4 C5 5A D0 EXTERNAL CONTROL THROUGH RS-232C The RS-232C port allows you connect the RS-232C input jack to an external control device (such as a computer or an A/V control system) to control the TV's functions externally. I Note: RS-232C on this unit is intended to be used with third party RS-232 control hardware and software. The instructions below are provided to help with programming software or to test functionality using telenet software. RS-232C Setup B IN AUDIO (RGB/DVI) REMOTE SERVICE CONTROL IN DIGITAL AUDIO OUT OPTICAL PONENT IN RS-232C IN (CONTROL & SERVICE) AUDIO OUT AUDIO S-VIDEO VIDEO (MONO) AUDIO AV IN 1 PC Type of Connector; D-Sub 9-Pin Male No. 1 2 3 4 5 6 7 8 9 Pin Name No connection RXD (Receive data) TXD (Transmit data) DTR (DTE side ready) GND DSR (DCE side ready) RTS (Ready to send) CTS (Clear to send) No Connection 1 5 APPENDIX 6 9 89 APPENDIX RS-232C Configurations Either cable below can be used. 7-Wire Configuration (Serial female-female NULL modem cable) PC RXD TXD GND DTR DSR RTS CTS 2 3 5 4 6 7 8 D-Sub 9 TV 3 2 5 6 4 8 7 D-Sub 9 TXD RXD GND DSR DTR CTS RTS RXD TXD GND DTR DSR RTS CTS 3-Wire Configurations (Not standard) PC 2 3 5 4 6 7 8 D-Sub 9 TV 3 2 5 6 4 7 8 D-Sub 9 HT - TXD RXD GND DTR DSR RTS CTS Set ID Use this function to specify a TV ID number. G p. 93. MENU BRIG BRIG HT + ENTER EXIT TIMER SIMPLI RATIO NK 1 Press the M E N U button and then use D or E button to select the OPTION menu. Language Input Label SimpLink Key Lock Caption : English : Off : Off : Off : Orbiter : Off :1 2 APPENDIX Press the G button and then use D or E button to select Set ID. ISM Method Low Power Set ID 3 Press the G button and then use D or E button to adjust Set ID to choose the desired TV ID number. The adjustment range of Set ID is 1~99. 1 Language Input label SimpLink Key Lock Caption 4 Press E X I T button to return to TV viewing or press M E N U button to return to the previous menu. ISM Method Low Power Set ID G 1 Communication Parameters Baud rate: 9600 bps (UART) Data length: 8 bits I Parity: None I I 2 3 Stop bit: 1 bit Communication code: ASCII code I Use a crossed (reverse) cable. I I 90 !NOTE G This product has command echo back in the RS-232C Command. Command Reference List COMMAND1 COMMAND2 DATA (Hexadecimal) COMMAND1 COMMAND2 DATA (Hexadecimal) 01. Remote Control Lock Mode k k x k k k k k k k k k k k a b b c d e f g h i j k l m 0~1 (G p. 92) (G p. 92) (G p. 92) 0~1 0~1 0 ~ 64 0 ~ 64 0 ~ 64 0 ~ 64 0 ~ 64 0 ~ 64 0~1 0~1 15. LCD TV Model Only Plasma TV Model Only k k k k k k k j j m m m r s t u v w $ p q b c g 0 ~ 64 0 ~ 64 0 ~ 64 0~3 0 ~ C8 0 ~ C8 0 ~ C8 (G p. 94) 0~1 0~1 (G p. 95) 0 ~ 64 COMMAND1 COMMAND2 DATA0 DATA1 DATA2 DATA3 DATA4 DATA5 (Hexadecimal) (Hexadecimal) (Hexadecimal) (Hexadecimal) (Hexadecimal) (Hexadecimal) 24. Channel Tuning m a physical major major low program high program low minor high minor low attribute Transmission / Receiving Protocol Transmission [Command1][Command2][ ][Set ID][ ][Data][Cr] [Command 1]: First command to control the set. (j, k, m or x) [Command 2]: Second command to control the set. [Set ID] : You can adjust the set ID to choose desired TV ID number in Setup menu. When selecting Set ID `0', every connected the TV is controlled. Set ID is indicated as decimal (1~ 99) on menu and as Hexa decimal (0x0~ 0x63) on transmission /receiving protocol. Transmit the `FF' data to read status of command. [Cr]: Carriage Return ASCII code `0x0D' [ ]: ASCII code `space (0x20)' * In this model, TV will not send the status during the standby mode. OK Acknowledgement [Command2][ ][Set ID][ ][OK][Data][x] The TV transmits ACK (acknowledgement) based on this format when receiving normal data. At this time, if the data is data read mode, it indicates present status data. If the data is data write mode, it returns the data of the PC computer. * In this model, TV will not send the status during the standby mode. * Data Format [Command 2]: Use as command. [. . . ] The covered code is a "commercial item, " as that term is defined in 48 C. F. R. 1995), consisting of "commercial computer software" and "commercial computer software documentation, " as such terms are used in 48 C. F. R. 227 . 7202-1 through 227 . 7202-4 (June 1995), all U. S. Government end users acquire covered code with only those rights set forth herein. 108 APPENDIX 1 MISCELLANEOUS. [. . . ]