User manual LG 32LN575V

[. . . ] The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. NOTE TO CABLE/TV INSTALLER: This reminder is provided to call the CATV system installer's attention to Article 820-40 of the National Electric Code (U. S. A. ). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of the cable entry as practical. REGULATORY INFORMATION This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. [. . . ] If there is no activity for 3 minutes, the notification screen automatically closes and completes the highlighted item (hide reminders). If you choose Hide Reminders, the window closes for the show or shows, but does not affect other Reminders you set. Note: If more than 2 reminders are set for the same time, arrows appear on the Reminder screen. Use the D / E button to view the shows. Remind Conflict A conflict message appears for the following reasons: · A show set with an Auto-Tune Reminder has the same start time as an existing Auto-Tune Reminder. · If you are using a cable box, a show set with an Auto-Tune Reminder overlaps with a Recording already scheduled. Select one of these options: · Auto-tune anyway - this show will override an existing show set to auto-tune · Proceed, no auto-tune - set the show as a Reminder but do not auto-tune · Don't set this reminder - cancel the Reminder 68 Operation Operation Basic operation Turning on the TV 1. At this moment, the TV switches to standby mode. In standby mode to turn TV on, press the ON/OFF, TV/VIDEO, CH D / E button on the TV or press the POWER, TV INPUT, TV/VIDEO, CH D / E, Number (0 ~ 9) button on the remote control . Select the viewing source by using TV INPUT, TV/VIDEO button on the remote control. This TV is programmed to remember which power state it was last set to, even if the power cord is out. When finished using the TV, press the POWER button on the remote control. Press the G button and then use D Press the G button and then use D and CADTV. Press the G button and then use ber you want to add or delete. /E /E button to select Manual Scan. button to select TV, DTV, CATV, D /E button to select channel num- Press the ENTER button to add or delete for the channel number. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. Analog antenna (over-the-air) TV signal Digital antenna (over-the-air) TV signal CATV CADTV Analog cable TV signal Digital cable TV signal 71 Operation Setup Menu Options continued Channel Edit SETUP G VIDEO AUDIO TIME OPTION LOCK CABLE EZ Scan Manual Scan Channel Edit DTV Signal Channel Label Main Input Sub Input Input Label Set ID SETUP VIDEO AUDIO TIME OPTION LOCK CABLE EZ Scan Manual Scan Channel Edit DTV Signal Channel Label Main Input Sub Input Input Label Set ID MENU Previous G Selection ( G or ) leads you to the channel edit screen. - Create two different types of channel lists in memory: "Custom list" and "Favorite channel list" from the default channel list created from the EZ Scan channel search. - A custom list can be created by toggling each channel on or off with ENTER button. The channels in the Custom List are displayed in black color, and the channels deleted from the Custom List are displayed in gray color. Once a channel is highlighted you can add or delete the channel by referring to the small window at the top-left corner of the screen. - You can create your own favorite channel list. Use the FAV button on the remote control when a channel is highlighted and then you can add or delete the channel to/from the Favorite List. - When a cable box connects to the physical channel 2, 3, or 4 in TV Guide On Screen system Setup, cable channels (CATV or CADTV) will not be editable by Channel Edit. Instead, use the cable box's Channel Edit if available. 72 1 2 3 4 Press the MENU button and then use D / E button to select the SETUP menu. [. . . ] · Are batteries installed with correct polarity (+ to +, - to -)?· Correct remote operating mode set: TV, VCR etc. ?· Check the power control settings. Power interrupted · No broadcast on station tuned with Auto off activated. The remote control doesn't work Power is suddenly turned off The video function does not work. · Check whether the product is turned on. [. . . ]