User manual LG 32PC5DVC-UG

[. . . ] Model Description MODEL SUFFIX 32PC5DVC-UG USA BRAND Product Name LG Park SY 07. 12. 10 KANG KWANG SUK 07. 12. 10 Part No. 32PC5DVC MFL34797052 (0808-REV02) 2. Printing Specification 1. Printing Colors · Cover : 1 COLOR (BLACK) · Inside : 1 COLOR (BLACK) 3. Stock (Paper) · Cover : Coated paper , S/White 150 g/ · Inside : Uncoated paper , 60 g/ 4. [. . . ] Dispose of used batteries in a recycle bin to preserve environment. I POWER TV SAP PICTURE INPUT SOUND TIMER 1 4 7 - 2 5 8 0 3 6 9 FAV 9 MFL34797052-en 8/6/08 1:59 AM Page 10 PREPARATION STAND INSTALLATION I Here shown may be somewhat different from your TV. Carefully place the product screen side down on a cushioned surface that will protect product and screen from damage. 10 PREPARATION 1 2 Assemble the product stand with the product as shown. 3 Install the 4 bolts securely, in the back of the product in the holes provided. BACK COVER FOR WIRE ARRANGEMENT Arrange the cables as shown picture. MFL34797052-en 8/6/08 1:59 AM Page 11 ATTACHING THE TV TO A WALL I I You should purchase necessary components to prevent TV from falling off of the stand. Here shown may be somewhat different from your TV. We recommend that you set up the TV close to a wall so it cannot fall over if pushed backwards. Additionally, we recommend that the TV be attached to a wall so it cannot be pulled in a forward direction, potentially causing injury or damaging the product. Caution: Please make sure that children don't climb on or hang from the TV. PREPARATION I Insert the eye-bolts or TV brackets and bolts to tighten the product to the wall as shown in the picture. * If your product has the bolts in the eye-bolts position before inserting the bolts, loosen the bolts. Secure the wall brackets with the bolts (not provided as parts of the product, must purchase separately) to the wall. Match the height of the bracket that is mounted on the wall to the holes in the product. Ensure the eye-bolts or brackets are tightened securely. Use a sturdy rope (not provided as parts of the product, must purchase separately) to tie the product. It is safer to tie the rope so it becomes horizontal between the wall and the product. I USE POWER CORD HOLDER I Here shown may be somewhat different from your TV. After connecting the power cord to the AC input terminal, remove the bolt at the hole on the back cover and fix the power cord at the rear side of the TV by using the bracket for fixing the power cord. 11 MFL34797052-en 8/6/08 1:59 AM Page 12 PREPARATION DESKTOP PEDESTAL INSTALLATION For proper ventilation, allow a clearance of 4 inches on all four sides from the wall. 12 PREPARATION 4 inches 4 inches 4 inches 4 inches CAUTION G Ensure adequate ventilation by following the clearance recommendations. PROTECTION COVER When installing the wall-mounted unit, use the protection cover for desk-type stand installation. MFL34797052-en 8/6/08 1:59 AM Page 13 ANTENNA OR CABLE CONNECTION 1. Antenna (Analog or Digital) PREPARATION Wall Antenna Socket or Outdoor Antenna without a Cable Box Connections. For optimum picture quality, adjust antenna direction if needed. Multi-family Dwellings/Apartments (Connect to wall antenna socket) ANTENNA/CABLE IN Wall Antenna Socket Outdoor Antenna (VHF, UHF) RF Coaxial Wire (75 ohm) Single-family Dwellings /Houses (Connect to wall jack for outdoor antenna) Copper Wire Be careful not to bend the bronze wire when connecting the antenna. 2. Cable Cable TV Wall Jack RF Coaxial Wire (75 ohm) ANTENNA/CABLE IN UHF Antenna VHF Signal Amplifier ANTENNA/CABLE IN To improve the picture quality in a poor signal area, please purchase a signal amplifier and install properly. If the antenna needs to be split for two TV's, install a 2-Way Signal Splitter. I If the antenna is not installed properly, contact your dealer for assistance. I I !NOTE G The TV will let you know when the analog, cable, and digital channel scans are complete. 13 MFL34797052-en 8/6/08 1:59 AM Page 14 EXTERNAL EQUIPMENT SETUP HD RECEIVER SETUP This TV can receive Digital Over-the-air/Cable signals without an external digital set-top box. However, if you do receive digital signals from a digital set-top box or other digital external device, refer to the figure as shown below. When connecting Component cable 1. How to connect 1 Connect the video outputs (Y, PB, PR) of the digital set top box to the C O M P O N E N T I N ( Y , PB , PR ) jacks on the set. Match the jack colors (Y = green, PB = blue, and PR = red). Connect the audio output of the digital set-top box to the C O M P O N E N T I N ( L , R ) jacks on the set. GB IN PC) COMPONENT IN 14 EXTERNAL EQUIPMENT SETUP UDIO IN GB/DVI) HEADPHONE AV IN 2 EXCLUSIVE SERVICE 1 2 2. [. . . ] I Ensure that the batteries are installed with correct polarity (+ to +, - to -). I Ensure that the correct remote operating mode is set: TV, VCR etc. I No broadcast on station tuned with Auto off activated. I I Power is suddenly turned off 22 APPENDIX The video function does not work. I Is the power cord inserted into wall power outlet? [. . . ]