User manual LG 426000

[. . . ] ENGLISH LCD TV PLASMA TV OWNER'S MANUAL LCD TV MODELS 3 2 L G 6 0* * 3 7 L G 6 0* * 4 2 L G 6 0* * 4 2 L G 6 1* * 4 7 L G 6 0* * PLASMA TV MODELS 3 2 P G 6 0* * 4 2 P G 6 0* * 5 0 P G 6 0* * 5 0 P G 7 0* * 6 0 P G 7 0* * 50PG40** Please read this manual carefully before operating your TV. Record model number and serial number of the TV. Refer to the label on the back cover and quote this information. To your dealer when requiring service. Trade Mark of the DVB Digital Video Broadcasting Project (1991 to 1996) I D N u m b e r ( s ) : 5102: 32LG6000-ZA 5103: 37LG6000-ZA 5104: 42LG6000-ZA 5484: 42LG6100-ZB 5105: 47LG6000-ZA 5571: 42LG6000-ZG 5572: 47LG6000-ZG 5719: 42LG6100-ZH 5251: 32PG6000-ZA 5252: 32PG6010-ZE 5100: 42PG6000-ZA 5249: 42PG6010-ZE 5101: 50PG6000-ZA 5250: 50PG6010-ZE 5245: 50PG7000-ZB 5244: 60PG7000-ZB 5246: 50PG4000-ZA ACCESSORIES Ensure that the following accessories are included with your TV. [. . . ] Language selection for dual language broadcast If a programme can be received in two languages (dual language), you can switch to DUAL I, DUAL II or DUAL I+II. DUAL I DUAL II DUAL I+II A Sends the primary broadcast language to the loudspeakers. Sends the secondary broadcast language to the loudspeakers. Sends a separate language to each loudspeaker. 91 SOUND & LANGUAGE CONTROL NICAM Reception (In Analogue Mode Only) If the TV is equipped with a receiver for NICAM reception, high quality NICAM (Near Instantaneous Companding Audio Multiplex) digital sound can be received. Sound output can be selected according to the type of broadcast received. 1 2 When NICAM mono is received, you can select N I C A M M O N O or F M M O N O. When NICAM stereo is received, you can select N I C A M S T E R E O or F M M O N O. If the stereo signal is weak, switch to F M M O N O. 3 When NICAM dual is received, you can select N I C A M D U A L I, N I C A M D U A L I I or N I C A M D U A L I + I I or F M M O N O. 92 SOUND & LANGUAGE CONTROL Speaker Sound Output Selection In AV, Component, RGB and HDMI mode, you can select output sound for the left and right loudspeakers. Select the sound output. L + R : Audio signal from audio L input is sent to the left loudspeaker and audio signal from audio R input is sent to the right loudspeaker. L + L : Audio signal from audio L input is sent to left and right loudspeakers. R + R : Audio signal from audio R input is sent to left and right loudspeakers. ON-SCREEN MENU LANGUAGE / COUNTRY SELECTION The installation guide menu appears on the TV screen when it is switched on for the first time. 1 OK Select your desired language. 2 OK Select your country. * If you want to change Language/ Country selection 1 2 MENU Select O P T I O N. OK Select M e n u L a n g u a g e or C o u n t r y. SOUND & LANGUAGE CONTROL 3 OK Select your desired language or country. 4 OK Save. · Press the M E N U button to return to normal TV viewing. · Press the R E T U R N button to move to the previous menu screen. !NOTE If you do not finish the set-up I n s t a l l a t i o n G u i d e by pressing R E T U R N or if you time out on the OSD (On Screen Display) the installation menu will continuously appear until the set up is completed whenever the TV is switched on G If you select the wrong local country, teletext may not appear correctly on the screen and some problems may occur during teletext operation. G The CI (Common Interface) function may not be applied based on country broadcasting circumstances. G DTV mode control buttons may not function based on country broadcasting circumstances. G In country that Digital broadcasting regulation isn't fixed, some DTV function may not work depending on digital broadcasting circumstances. G The Country Setting "UK" should only be activated in UK. G 93 SOUND & LANGUAGE CONTROL LANGUAGE SELECTION (IN DIGITAL MODE ONLY) The Audio function allows selection of a preferred language. If audio data in a selected language is not broadcast, the default language audio will be played. Use the Subtitle function when two or more subtitle languages are broadcast. If subtitle data in a selected language is not broadcast, the default language subtitle will be displayed. When the languages you selected as the primary for Audio Language and Subtitle Language are not supported, you can select language in secondary category. 1 MENU 2 OK Select O P T I O N. 1 MENU 2 OK Select O P T I O N. Select A u d i o L a n g u a g e or S u b t i t l e L a n g u a g e. Select your desired language. Select Hard of Hearing( ). 3 OK 3 OK Select O n or O f f. 4 OK Save. · Press the R E T U R N button to move to the previous menu screen. 94 SOUND & LANGUAGE CONTROL < Audio Language Selection > G When two or more audio languages are broadcast, you can select the audio language. Audio Language OSD Information Display N. A Status Not Available MPEG Audio Dolby Digital Audio Audio for "Visual Impaired" Audio for "Hearing Impaired" 1Q. MENU 2 OK Select A u d i o Select an audio language. 3 Select L+R, L+L or R+R. < Subtitle Language Selection > G When two or more subtitle languages are broadcast, you can select the subtitle language with the SUBTITLE button on the remote control. G Press the Subtitle Language OSD Information Display N. A Status Not Available Teletext Subtitle Subtitle for "Hard of Hearing" - The audio/subtitles can be displayed in a simpler form with 1 to 3 characters broadcast by the service provider. - When you select supplementary Audio (Audio for "Visual/Hearing Impaired") the TV may output a part of the Main audio. TIME SETTING CLOCK SETUP The clock is set automatically when receiving a digital signal. [. . . ] 1995), consisting of "commercial computer software" and "commercial computer software documentation, " as such terms are used in 48 C. F. R. 227. 7202-1 through 227. 7202-4 (June 1995), all U. S. Government End Users acquire Covered Code with only those rights set forth herein. This License represents the complete agreement concerning subject matter hereof. [. . . ]