User manual LG 42PC5R

[. . . ] Number of pages : 32 N O T E S "This part contain Eco-hazardous substances (Pb, Cd, Hg, Cr6+, PBB, PBDE, etc. ) within LG standard level, Details should be followed Eco-SCM management standard[LG(56)-A-2524]. Especially, Part should be followed and controlled the following specification. (1)Eco-hazardous substances test report should be submitted when Part certification test and First Mass Production. (2) Especially, Don't use or contain lead(Pb) and cadmium(Cd) in ink. 3. Special Instructions * LGENT : Printed in China * LGENP : Printed in China * LGEIL : Printed in India * LGEDI : Printed in Indonesia * LGEIN : Printed in Indonesia * LGEMA : Printed in Poland * LGETH : Printed in Thailand * LGEWA : Printed in U. K. [. . . ] Close cover. AUDIO BRIGHT BRIGHT MENU BRIGHT + MENU BRIGHT + I I Use a remote control up to 7 meters distance and 30 degree (left/right) within the receiving unit scope. Dispose of used batteries in a recycle bin to preserve environment. I I 11 MFL34797033-en-simple 11/1/07 2:35 PM Page 12 PREPARATION BACK COVER FOR WIRE ARRANGEMENT I Here shown may be somewhat different from your TV. Plasma TV Model 12 PREPARATION 1 Hold the CABLE MANAGEMENT with both hands and pull it backward as shown. CABLE MANAGEMENT 2 Connect the cables as necessary. To connect an additional equipment, see the EXTERNAL EQUIPMENT SETUP section. 3 Install the CABLE MANAGEMENT as shown. MFL34797033-en-simple 11/1/07 2:35 PM Page 13 LCD TV Model PREPARATION 1 Connect the cables as necessary. To connect an additional equipment, see the EXTERNAL EQUIPMENT SETUP section. 2 Install the CABLE MANAGEMENT as shown. CABLE MANAGEMENT 3 Bundle the cables using the supplied TWISTER HOLDER. (This feature is not available for all models. ) !NOTE G Do not hold the CABLE MANAGEMENT when moving the product. - If the product is dropped, you may be injured or the product may be broken. TWISTER HOLDER How to remove the CABLE MANAGEMENT G Hold the CABLE MANAGEMENT with both hands and pull it backward. 13 MFL34797033-en-simple 11/1/07 2:35 PM Page 14 PREPARATION ATTACHING THE TV TO A WALL I I This feature is not available for all models. Here shown may be somewhat different from your TV. We recommend that you set up the TV close to a wall so it cannot fall over if pushed backwards. Additionally, we recommend that the TV be attached to a wall so it cannot be pulled in a forward direction, potentially causing injury or damaging the product. Caution: Please make sure that children don't climb on or hang from the TV. 14 PREPARATION I Plasma TV Model LCD TV Model Insert the eye-bolts (or TV brackets and bolts) to tighten the product to the wall as shown in the picture. If connected to C O M P O N E N T I N 2 input, select C o m p o n e n t 2 input source. Component 1/2 Yes Yes Yes Yes Yes HDMI1/DVI, HDMI2 No Yes Yes Yes Yes Y, CB/PB, CR/PR Resolution 720x480i 720x480p 1280x720p 1920x1080i Horizontal Frequency(KHz) 15. 73 15. 73 31. 47 31. 50 44. 96 45. 00 33. 72 33. 75 26. 97 27 . 00 33. 71 33. 75 67 . 432 67 . 50 Vertical Frequency(Hz) 59. 94 60. 00 59. 94 60. 00 59. 94 60. 00 ( 59. 94 60. 00 ) Y PB PR L R I I Signal 480i 480p 720p 1080i 1080p 1920x1080p 23. 976 24. 00 29. 97 30. 00 59. 94 60. 00 17 MFL34797033-en-simple 11/1/07 2:35 PM Page 18 EXTERNAL EQUIPMENT SETUP DVD SETUP When connecting Component cable 1. How to connect 1 EXTERNAL EQUIPMENT SETUP Connect the video outputs (Y, PB, PR) of the DVD to the C O M P O N E N T I N V I D E O 1 jacks on the set. Match the jack colors (Y = green, PB = blue, and PR = red). Connect the audio outputs of the DVD to the C O M P O N E N T I N A U D I O 1 jacks on the set. I/DVI IN COMPONENT IN 2 R (CONT 1 VIDEO AUDIO S- ( ) 2 2. How to use I 1 2 Turn on the DVD player, insert a DVD. Select C o m p o n e n t 1 input source by using the I N P U T button on the remote control. If connected to C O M P O N E N T I N 2 input, select C o m p o n e n t 2 input source. Refer to the DVD player's manual for operating instructions. Y PB PR L R I I I When connecting HDMI cable 1. How to connect 1 2 Connect the HDMI output of the DVD to the H D M I / D V I I N 1 or H D M I I N 2 jack on the set. No separated audio connection is necessary. [. . . ] Ensure you are pointing the remote control directly at the TV. I Ensure that the batteries are installed with correct polarity (+ to +, - to -). I Ensure that the correct remote operating mode is set: TV, VCR etc. I No broadcast on station tuned with Auto off activated. I I Power is suddenly turned off 26 APPENDIX The video function does not work. [. . . ]