User manual LG 42PN450B

[. . . ] Model Description Model name 2nd, 3rd Suffix : : 42PN450D-ZA PI (Eng/Ita) Brand name Product name : : LG 42PN450D Part number (Revision number) : MFL67710004 (1301-REV00) 2. Number of pages N O T E : : : : : : Uncoated, wood-free paper 60 g/㎡ Uncoated, wood-free paper 60 g/㎡ Off set Saddle stitching Eng/Ita (2) 64 : : 1 Color (Black) 1 Color (Black) : 182 mm x 257 mm (B5) “This part contains Eco-hazardous substances (Pb, Cd, Hg, Cr6+, PBB, PBDE, etc. ) within LG standard level, Details should be followed Eco-SCM management standard[LG(56)-A-2524]. Especially, Part should be followed and controlled the following specification. [. . . ] Place the ferrite core close to the TV and a wall plug. [to a wall plug] [Figure 1] 2 Use the ferrite core to reduce the electromagnetic interference in the cable. Wind the component Y, Pb, Pr, L, R cable on the ferrite core once. [to an External device] [to the TV] 10 mm(+ / - 5 mm) ENGLISH [to the TV] (Black) [Cross Section of Ferrite Core] [Figure 2-1] Gather and bind the component Y, Pb, Pr, L, R and scart cable with the ferrite core. [to an External device] [to the TV] (Black) [Cross Section of Ferrite Core] [Figure 2-2] Wind the PC audio cable on the ferrite core once. [to an External device] 10 mm(+ / - 5 mm) [to the TV] [Figure 2-3] 10 mm(+ / - 5 mm) 3 Use the ferrite core to reduce the electromagnetic interference in the LAN cable. Wind the LAN cable once on the ferrite core B and thrice on the ferrite core A. Place the ferrite core close to the TV and an External device. A (Gray) B (Gray) [to the TV] B A [Figure 3] - If there are three ferrite cores, follow as shown in Figures 1 and 2. - If there is LAN port, additionally follow as shown in Figure 3. For yy an optimal connection, HDMI cables and USB devices should have bezels less than 10 mm thick and 18 mm width. Use an extension cable that supports USB 2. 0 if the USB cable or USB memory stick does not fit into your TV’s USB port. *A *B 10 mm 18 mm [to an External device] [Cross Section of Ferrite Core] ASSEMBLING AND PREPARING 13 NOTE yy Antenna Isolator Installation Guide -- Use this to install TV in a place where there is a voltage difference between TV Set and GND of antenna signal. »» If there is a voltage difference between TV Set and GND of antenna signal, the antenna contact might be heated and excessive heat might cause an accident. -- You can improve the safety when watching TV by efficiently removing power voltage from TV antenna. It is recommended to mount the isolator to the wall. If it cannot be mounted to the wall, mount it on the TV. Avoid disconnecting the antenna Isolator after installation. -- Before starting, be sure that the TV antenna is connected. Cable / Antenna Connect one end of the isolator to cable/antenna jack and the other to TV set or set-top box. €œEquipment connected to the protective earthing of the building installation through the mains connection or through other equipment with a connection to protective earthing - and to a cable distribution system using coaxial cable, may in some circumstances create a fire hazard. [. . . ] Looking at the laser beam may damage your vision. Yy Audio with ACP (Audio Copy Protection) function may block digital audio output. This feature is not available in all countries. USB NOTE yy Check if the CI module is inserted into the PCMCIA card slot in the right direction. [. . . ]