User manual LG 505G(K)

[. . . ] 1 1 1 1 2 2 3 3 3 4 5 7 8 8 8 8 9 10 Special notes on LCD monitors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Package contents Installation instructions Placement Installation External controls Image adjustment Screen adjustment Attachments Plug and play Power saver Troubleshooting Technical specifications Display modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Turn off the power switch and then turn it on again to make the flicker disappear. You may find slightly uneven brightness on the screen depending on the desktop pattern you use. The LCD screen has effective pixels of 99. 99% or more. It may include blemishes of 0. 01% or less (caused by a missing pixel or a pixel that is always lit). When the same image is displayed for hours on end, its afterimage may remain after switching to a new image. When this happens, the screen will recover slowly by changing the image. Turning the LCD monitor off for several hours will also correct this problem. Package contents LCD display (with speakers) D-Sub signal cable DVI signal cable (optional) Quick Start Guide Power cable Audio cable User's Guide (CD) 2 Installation instructions Placement Note: Read the Safety section carefully before starting the installation. When installing your LCD monitor, consider the placement of the monitor: To minimize the reflection of the monitor, protect your eyes, and ensure premium quality, don't install your LCD monitor near windows or where there is backlight. Keep the monitor at least 30 cm away from your eyes. The upper edge of the monitor should be just a little higher than your line of sight. Adjust the front and back dip angles of the monitor, so that you can view the display comfortably. To change other Bright/Contract Adjustment Phase/Clock pulse Adjustment Horizontal/Vertical Adjustment Color Temp. Adjustment Language Selection OSD Setting Auto Adjustment Message Restore Exit (Analog) 5 Image adjustment for digital The image settings of your LCD monitor were adjusted to their optimal status for digital TV before shipment. If you want to adjust the image settings to suit your personal preference, follow the steps below: 1. Click Menu to display the OSD window as shown in the following figure. Click Plus or Minus to select the function to be adjusted as shown in the following figure. Click the Menu again to select the function to be adjusted. Click Plus or Minus to change current settings. To exit the OSD window, select " settings, repeat steps 2-4. To change other Bright/Contrast Adjustment Phase/Clock Pulse Adjustment Horizontal/Vertical Adjustment Color Temp. Adjustment Language Selection OSD Setting Input Selection Message Restore Exit (Digital) 6 Screen adjustment Function Definition Primary directory symbol Secondary directory symbol Secondary directory Description items Contrast Brightness Phase Clock pulse Horizontal Vertical N/A N/A Warm color temperature Cold color temperature User Definition/Red User Definition/Green User Definition/Blue N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A English Deutsch Français Español Italiano Hollands Suomalainen Horizontal Vertical OSD time display Moves OSD left and right. Sets up horizontal, vertical, sequence and focus automatically (for analog input only). [. . . ] The LCD monitor has a built-in Power Control System (Power Saver). When the LCD monitor is not operated for a period of time, the Power Control System automatically sets the system at low voltage status to save power. Move the mouse slightly or press any key to return to normal operation. The Power Saver function can only be operated by the display card of the computer system. [. . . ]