User manual LG 50LB5820

[. . . ] The openings shall be never be blocked by placing the product on a bed, sofa, rug or other similar surface. This product shall not be placed in a builtin installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instruction has been adhered to. CAUTION concerning the Power Cord Most appliances recommend they be placed upon a dedicated circuit; That is, a single outlet circuit which powers only that appliance and has no additional outlets or branch circuits. Check the specification page of this owner’s manual to be certain. [. . . ] Sampling Frequency within 32 to 48 kHz within 32 to 48 kHz within 32 to 48 kHz within 32 to 192 kHz within 32 to 48 kHz Bitrate within 80 to 320 kbps within 56 to 128 kbps within 50 to 500 kbps within 500 to 5000 kbps within 500 to 5000 kbps 50LB5820-NB_DDEULLK_ENG. indd 15 2014-01-06 5:08:40 16 Operating Basic operations USB operation 1. Connect the USB device to the USB port. 2. Select the USB function by pressing FUNCTION on the remote control or F on the unit until the function is selected. Do this The resume point may be cleared when you pull out the power cord or removing the USB device from the unit. Note , , Other operations DRC (Dynamic Range Control) Make the sound clear when the volume is turned down (Dolby Digital only). Set to [DRC ON] by using DRC. 3 Operating Pause During playback, press V on the remote control to go to the next file. Playing less than 2 seconds, press C on the remote Skip to the next/ control to go to the previous previous file file. Playing after 3 seconds, press C on the remote control to go to the beginning of the file. Search for a section within a file Press and hold C/V during playback and release it at the point you want to listen to. (except FLAC and OGG files) Press REPEAT on the remote control repeatedly, the display will be changed in the following order, OFF RPT 1 RPT DIR (DIRECTORY) RPT ALL RANDOM. Press 0 to 9 numerical buttons on the remote control to go to the desired file directly. This unit memorizes a current song which is played before changing the function or turning off the unit. AV Sync When receiving audio signals from TV, sound and images may not be matched. In the case, this function can adjust the delay time. If you use TV's remote control again, the unit synchronizes with the TV. yy When the connection fails, make sure of the condition of the TV and power. yy Make sure of the condition of this unit and the connection in the cases below when using LG Sound Sync. -- Disconnecting the wireless connection caused by interference or a distance. yy The amount of time to turn off this unit is different depending on your TV when you set AUTO POWER function to ON. Note , , 2. Set up LG Sound Sync (Optical) on the TV. Refer to the TV's instruction manual. 3. Turn on the unit by pressing 1 (Power) on the remote control. 4. Select OPTICAL function by using FUNCTION on the remote control or F on the unit until the function is selected. You can see "LG OPT" on the display window if connecting normally between this unit and your TV. 50LB5820-NB_DDEULLK_ENG. indd 18 2014-01-06 5:08:41 Operating 19 With wireless connection 1. Turn on the unit by pressing 1 (Power) on the remote control. 2. Select LG TV function by using FUNCTION on the remote control or F on the unit until the function is selected. 3. Set up LG Sound Sync (Wireless) on the TV. [. . . ] yy There is an obstacle in the path of the remote control and the unit. yy The batteries in the remote control is exhausted. Replace the batteries with new one. No sound No woofer sound No display 4 Troubleshooting The AUTO POWER function does not work. yy Depending on the connected device, this function may not operate. Check the details below and adjust the unit according to them. yy Switch [ON] state of DRC function to [OFF] by using remote controller. [. . . ]