User manual LG 55LB731V

[. . . ] “Dolby” and the double-D symbol are trademarks of Dolby Laboratories. The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries. ABOUT DIVX VIDEO: DivX® is a digital video format created by DivX, LLC, a subsidiary of Rovi Corporation. This is an official DivX Certified® device that plays DivX video. [. . . ] yy Do not install in direct sunlight or near a heat source. yy Magnetic objects, such as speakers, may interfere with the camera’s operation. yy Install the product in a place with moderate temperature and humidity. The recommended temperature range is 0 °C to 40 °C. yy Strong electromagnetic waves from other devices could interfere with the camera’s operation. yy Remove all the protective plastic bags (Vinyl) before use. The product and company names contained in this manual may or may not be registered trademarks or copyrights, and are only used for identification or explanatory purposes. All trademarks reserved. Overview ENGLISH ENG Microphones Lens Stand Activity Indicator Stand-Arm Stand-cable holder Stand-Bottom USB Cable 26 ASSEMBLING AND PREPARING Attaching the Video Call Camera 1 Unfold the stand and put it on the top center of the TV set. Video call camera NOTE yy For the best quality video and audio outputs, install the camera on the top-center of your TV. yy Set up with the television switched off. yy When using external speakers, allow sufficient space between the microphones and the speakers. If noise is present, change the PC output to another resolution, change the refresh rate to another rate or adjust the brightness and contrast on the PICTURE menu until the picture is clear. yy In PC mode, some resolution settings may not work properly depending on the graphics card. Connect the TV to a wall antenna socket with an RF cable (75 Ω). NOTE yy Use a signal splitter to use more than 2 TVs. yy If the image quality is poor, install a signal amplifier properly to improve the image quality. yy If the image quality is poor with an antenna connected, try to realign the antenna in the correct direction. yy An antenna cable and converter are not supplied. yy Supported DTV Audio: MPEG, Dolby Digital, Dolby Digital Plus, HE-AAC 28 MAKING CONNECTIONS Satellite dish Connection (Only satellite models) HDMI Connection ENGLISH ENG DVD / Blu-Ray / HD Cable Box / HD STB / PC Satellite Dish 13 / 18 V 700mA Max LNB IN Satellite IN HDMI (*Not Provided) Connect the TV to a satellite dish to a satellite socket with a satellite RF cable (75 Ω). Transmits the digital video and audio signals from an external device to the TV. Connect the external device and the TV with the HDMI cable as shown. It does not matter which port you use. NOTE yy It is recommended to use the TV with the HDMI connection for the best image quality. yy Use the latest High Speed HDMI™ Cable with CEC (Customer Electronics Control) function. yy High Speed HDMI™ Cables are tested to carry an HD signal up to 1080p and higher. [. . . ] Set ID = All = 00 Data 00 & 01 = Channel Data is 1 = 00 01 Data 02 = Digital Terrestrial TV = 10 Result = ma 00 00 01 10 3. Tune to the satellite (DVB-S) Channel 1000. Set ID = All = 00 Data 00 & 01 = Channel Data is 1000 = 03 E8 Data 02 = Digital Satellite TV = 40 Result = ma 00 03 E8 40 Ack [a][ ][Set ID][ ][OK][Data 00][Data 01][Data 02][x] [a][ ][Set ID][ ][NG][Data 00][x] Data 05: Input Source (Analogue) - 00 : Terrestrial TV (ATV) - 01 : Cable TV (CATV) * Digital Terrestrial/Cable Data 00 : xx (Don't care) [Data 01][Data 02]: Major Channel Number Data 01 : High byte Channel Data Data 02 : Low byte Channel Data - 00 01 ~ 27 0F (Decimal: 1 ~ 9999) [Data 03][Data 04]: Minor Channel Number Data 03 : High byte Channel Data Data 04 : Low byte Channel Data Data 05 : Input Source (Digital) - 02 :  errestrial TV (DTV) – Use Physical Channel T Number - 06 :  able TV (CADTV) – Use Physical Channel C Number - 22 :  errestrial TV (DTV) – Don’t Use Physical T Channel Number - 26 :  able TV (CADTV) - Don’t Use Physical C Channel Number - 46 :  able TV (CADTV) – Use Major Channel C Number Only (One Part Channel) Two bytes are available for each major and minor channel data, but usually the low byte is used alone (high byte is 0). * Tune Command Examples: 1.  une to the analogue cable (NTSC) channel 35. T Set ID = All = 00 Data 00 = Channel Data is 35 = 23 Data 01 & 02 = No Major = 00 00 Data 03 & 04 = No Minor = 00 00 Data 05 = Analogue Cable TV = 01 Total = ma 00 23 00 00 00 00 01 2.  une to the digital terrestrial (ATSC) channel 30-3. [. . . ]