User manual LG 71PY1M

[. . . ] Model Number : Serial Number : LG Electronics U. S. A. , Inc. Warning/Caution Warning/Caution WARNING/CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING/CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING/CAUTION: TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. POWER CORD POLARIZATION: CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. ATTENTION: POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU'AU FOND. NOTE TO CABLE/TV INSTALLER: This reminder is provided to call the CATV system installer's attention to Article 820-40 of the National Electric Code (U. S. A. ). [. . . ] Select one of these options: W auto-tune anyway - this show will override an existing show set to auto-tune W proceed, no auto-tune - set the show as a Reminder but do not auto-tune W don't set this reminder - cancel the Reminder 56 LCoS Projection TV Operation Operation Turning the TV On * In this manual, the OSD (On Screen Display) may be different from your TV's because it is just an example to help you with the TV operation. Turning on the TV just after installation 1. At this moment, the TV is switched to standby mode. Press the TV INPUT, INPUT, CH (D / E), Number (0 ~ 9) button on the remote control or press the CH (D / E) button on the TV front panel and then the TV will switch on. Turning on the TV (power cord is still connected) 1. If the TV was turned off with indicators on the TV · Check the power cable. If the TV was turned off with the remote control and the POWER button on the TV · Press the POWER button on the TV or press the POWER, INPUT, CH (D / ton on the remote control to turn the TV on. E), Number (0 ~ 9) but- Notes: · If you intend to be away on vacation, disconnect the power plug from the wall power outlet. · The TV Guide On Screen and any CableCARDTM Software upgrades work while the TV is in standby · mode. If you pull the power plug cord the TV Guide On Screen will not update its listings and no ··· · CableCARDTM Software upgrades will occur. · After turning on the TV, it could take up to a week for the TV Guide On Screen system to receive full list· ings data. Owner's Manual 57 Operation TV Setup On-screen Menus Language Selection - The menus can be shown on the screen in the selected language. Press the MENU button and then use menu. Press the G D / E button to select the OPTION button and then use D / E button to select Language. 3. Press the G button and then use D / E button to select your desired language. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. Note: · When a cable box connects to the physical channel 2, 3, or 4 in TV Guide On Screen Setup, cable channels(CATV or CADTV) will not be editable by Channel Edit. Instead, use the cable box's Channel Edit if available. DTV Signal Strength - Shows DTV signal levels which are received to your TV whether you need to adjust your antenna or digital cable input. The higher the signal strength, the less likely you are to experience picture degradation. - DTV Signals: Only when the input signal is DTV or CADTV, this function is available. Press the G button and then use D /E button to select the SETUP menu. D /E button to select DTV Signal. 3. View the on-screen signal strength monitor to see the quality of the signal being received. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. 60 LCoS Projection TV Operation Main Picture Source Selection - Changes the picture source so you can watch your off-air TV, cable TV, VCR, DVD, or any other devices that are connected to your TV. 1. Press the MENU button and then use menu. Press the G button and then use D /E button to select the SETUP D /E button to select Main Input. 3. Press the G button and then use D / E button to select the source: Antenna, Cable, AV1, AV2, AV3, Component1, Component2, RGB-DTV (or RGB-PC), HDMI1/DVI or HDMI2. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. Input Label 1. [. . . ] Contact the number below or your authorized LG®Brand repair facility for details. Before you call for warranty service, check your operating guide ­ you may avoid a service call. LG®Brand Customer Interactive Center P. Box 240007 201 James Record Road Huntsville, Alabama 35824 ATTN: CIC Telephone number: 1-800-243-0000 This number is a toll-free number Follow menu prompts when the call is answered Web address: www. lgservice. com Telephone Center Hours of Operation: 24 hours a day, 365 days per year Service for your LG®Brand Rear Projection Television is provided through LG Electronics Alabama, Inc. , the authorized LG®Brand Service Center for the United States. [. . . ]