User manual LG A09AW1

[. . . ] 11 Never store or ship the air conditioner upside down or sideways to avoid damage to the compressor. 12 If the remote control will not be used for a long time, remove the batteries. CAUTION The manufacturer does not assume responsibility for accidents or injury caused by an incorrectly installed air conditioner. If you are unsure about installation, contact an installation specialist. E-2 Contents x PREPARING YOUR AIR CONDITIONER s s s s s Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Description of Each Component . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] x - on the battery with - on the remote control. Close the cover by sliding it back until it clicks into place. 1 2 3 E-7 Cooling Your Room Remote Control Control Panel 1 You must select the Cool mode if you wish to lower the temperature in your room. Result: x The air conditioner starts up in the mode selected when the unit was last used. x The unit beeps twice. The air conditioner is fitted with a protection mechanism to prevent the unit from being damaged when it is started immediately after being: x Plugged in x Stopped It will start up normally after three minutes. 2 If the COOL indicator is not lit on the unit: x Press the COOL button on the remote control or x Press the Mode button on the unit one or more times until the COOL indicator lights up Result: x The unit beeps each time you press the COOL/Mode button. x The air conditioner starts up in the Cool mode. 3 You can change modes at any time. To adjust the temperature, press the Temperature buttons on the remote control or unit one or more times until the desired temperature is displayed. The temperature can be set between 64°F and 86°F. Result: x Each time you press the temperature buttons: ­ The temperature is adjusted by 1°F and displayed on the control panel ­ The unit beeps x The air conditioner starts cooling if the room temperature is higher than the selected temperature. 4 To set the fan speed: x Press the HIGH, MED or LOW button on the remote control as desired. or x Press the Fan Speed button on the unit one or more times until the desired Fan speed indicator lights up. 5 To control the direction of the air flow, refer to page 10. E-8 Ventilating Your Room If the air in your room is stale, you can air the room using the Fan feature. 1 If you wish to discharge stale air, push the ventilation lever on the front of the unit to the right and open position ( Result: ). x The air inside the room circulates and stale air is discharged outside. ). Otherwise, push the ventilation lever to the left and closed position ( Result: x The air simply circulates inside the room. Remote Control 2 If necessary, press the Result: (On/Off) button. Control Panel x The air conditioner starts up in the mode selected when the unit was last used. x The unit beeps twice. 3 If the FAN indicator is not lit on the unit: x Press the FAN button on the remote control or x Press the Mode button on the unit one or more times until the FAN indicator lights up Result: x The unit beeps each time you press the FAN/Mode button. x The remaining time is displayed and decreased by 1 hour automatically to indicate the remaining time. x The air conditioner will be controlled as illustration below. Remote Control Control Panel Cooling When the temperature has been increased by 2°F (after 1 hour), it is maintained for 7 hours. To Cancel the Sleep Timer To cancel the timer, press: x Sleep on the remote control. x The SLEEP indicator is no longer displayed. x The air conditioner operates in the mode selected last. If you select the Energy Saving mode in the Sleep Timer mode, the Sleep Timer will be cancelled and the air conditioner will start up in the Energy Saving mode. E-13 Selecting Energy Saving Mode Remote Control Control Panel 1 If you wish to save energy when using your air conditioner, select the energy saving mode with the Energy Saver button. (Be sure not to use benzene, solvent or other chemical products. ) Front grille Grille groove Body guide If you. . . Will not be using the air conditioner for a long period of time Then. . . x Set the fan to "FAN" and let it for a few hours to dry the inside of the air conditioner thoroughly. x Switch the air conditioner off and unplug it from the wall socket. Set the fan to "FAN" and let it run for a few hours to dry the inside of the air conditioner thoroughly. Have not used the air conditioner for a long period of time E-16 Solving Common Problems Before contacting an authorized service center, perform the following simple checks. They may save you the time and expense of an unnecessary call. Problem The air conditioner does not operate at all Explanation / Solution x Check that the circuit breaker used for the air conditioner has not been triggered. x Check that the power cable is plugged into a wall socket and the socket is switched on, if necessary. x Check that the temperature indicator on the unit is lit; if necessary, press (On/Off) on the remote control or unit. [. . . ] If during in-home service repair can not be completed, it may be necessary to remove, repair and return the product. If in-home service is unavailable, LG may elect, at our option, to provide for transportation of our choice to and from a LG authorized service center. Otherwise, transportation to and from the LG authorized service center is the responsibility of the purchaser. This limited warranty covers manufacturing defects in materials and workmanship encountered in normal, noncommercial use of this product and shall not apply to the following, including, but not limited to: delivery and installation; damage which occurs in shipment; applications and uses for which this product was not intended; failures or problems which are caused by products or equipment not supplied by LG; accidents, misuse, abuse, neglect, misapplication, fire, water, lightning or other acts of nature; incorrect electrical line voltage, fluctuations or surges; damage caused by improper or faulty installation; product alteration or modification; improper or unauthorized repair; cosmetic damage or exterior finish; product with altered serial numbers; failure to follow operating and environmental instructions that are covered and prescribed in the instruction book; customer adjustments, routine maintenance and cleaning; consumable items such as filters; use of non-LG or unauthorized parts, supplies, accessories or equipment which damage this product or result in service problems. [. . . ]