User manual LG A09AW1 SF0

[. . . ] Notational Failure to follow directions noted by this symbol could result in bodily harm or damage to equipment. Prohibited Important to read and understand at all times Do not disassemble Any change or modification not expressly approved by designated qualified personnel could avoid your authority to operate this device. Always make sure that the disc does not have a crack before use. If the disc has a crack (especially around the center hole), it is recommended to make a copy immediately and use the copy instead. When a cracked disc is used continuously, the size of the crack is likely to grow and this will eventually result in irreparable damage to the disc. [. . . ] Run the CDSETUP. EXE file in the Ddriver folder. When Setup is successfully completed, click OK button or press the Enter key. Reboot the computer. Manual Setup Make the C:\LG directory. Copy the files from the diskette to the C:\LG directory. * C:\LG after the C:\prompt and press [Enter]. Add the DEVICE=C:\LG\SSCDROM. SYS \D:SSCD000/V entry. Edit the AUTOEXEC. BAT file. Add the C:\LG\MSCDEX/D:SSCD000 entry. Reboot the computer. Using the Drive Using the COMBO Drive To play audio or video CDs and / or DVDs in your COMBO drive, proceed as follows. Push the power button and boot the computer. After booting the computer, open the disc compartment by pressing the Eject button. Insert the disc (CD/DVD) with the label on the disc facing upwards and close the disc compartment by pressing the Eject button. Play the disc (CD/DVD). Accessories The type of accessories varies depending on product model. User Manual & Setup Guide. Playing DVDs or Video CDs Software. Screws. Set up and run the SOFT MPEG program supplied as an accessory. Design and specifications are subject to change without prior notice. Us ing the D rive Storing and Cleaning Your Discs To ensure a long service life for your discs and drive, follow the pre-cautions below when storing and cleaning your discs. Do not place a disc in direct sunlight. Currently, the motionpicture industry has divided the worldinto different regions or zones thatcorrespond to the regional markets intowhich the motion picture industry releasesmovies. Simply put, RPC codes are placedon movies marketed throughout the world, based on the region of the world inwhich they are being sold. These RPCcodes help control and prevent piratingof new movies into other motion pictureregions prior to their true releasedates within those markets. The TS-H492C(A09AW1 SF0) COMBO drive supports RPCphase II. In the RPC-2 mode, the localcode can be changed by users. RPC-2is selected by default for the TS-H492C(A09AW1 SF0) COMBO drive. You can change the region code up tofive times via an MPEG application. Please contact your dealer or local LG representative if you wish tochange the local code more than fivetimes. Troubleshooting Solving Recording Problems If you have any problems in recording via your COMBO drive, follow the appropriate instructions below for the source that you are using. Hard Drive Check whether the source file is corrupted. Optimize the hard disk by using the Windows defragmenter feature: START / PROGRAMS / ACCESSORIES / SYSTEM TOOLS / DISC DEFRAGMENTER Decompress the hard disk if it is compressed. Make sure that the space available on the hard disk is at least twice the size of the largest file to be recorded on the disc. If you wish to record more than 1000 small files: First create an image file and copy the image file to the disc Choose the low record speed Compress small files and then record them Network Drive Copy the network drive contents to the hard disk and then from the hard disk to the COMBO drive. CD-ROM Drive Clean the source CD, if necessary. [. . . ] See the following procedure to set DMA transfer mode in windows oprerating system. (Windows 98/ME) + Select your COMBO drive + Click on START + Click on Settings + Select Control Panel + Select the System Icon + Select the Device Manager panel in System Properties + Click on the Properties button + Click on the Settings tab + Check the DMA checkbox to enables DMA. + Click OK + Restart your PC + Expand the CD-ROM icon Windows 2000/XP Select the DMA mode by selecting [Start > Setting > Control Panel > System > Device Manager > IDEATA/ATAPI Controller > Default/Assistant IDE Channel Advanced Information] Troubleshooting Solving Technical Problems Problem The COMBO drive is not detected by the computer. After installing the COMBO drive, the PC gets slower. Meaning / Solution Check that the power, audio and IDE cables are correctly connected to the computer. [. . . ]