User manual LG A246UQ UV3

[. . . ] Keep children away from the unit. 5 If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard. 6 Do NOT attempt to repair the unit yourself. If it is damaged in any waycontact: , An authorized service center The dealer from whom you purchased the air conditioner . 7 Do NOT place any blocking objects in front of the unit. 8 If the remote control will not be used for a long time, remove the batteries. 9 Before throwing out the device, it is necessary to pull back the battery cells and get rid of them safely . 10 The appliance is not intended for use by young children or infirm person without supervision; young children should be supervised to ensure that they do not play with the appliance. 11 Do NOT use an extension d with this pr cor oduct. CA U T I O N The manufacturer does not assume responsibility for accidents or injury caused by an incorrectly installed air conditioner If you are unsure about . [. . . ] Result: The unit beeps each time you press the / button. The air conditioner starts up in the Cool mode. You can change modes at any time. 3 To adjust the temperature, press the or buttons on the remote control or unit one or more times until the desired temperature is displayed. The temperature can be set between 64°F and 86°F . Result: Each time you press the or buttons: ­ The temperature is adjusted by 1°F and displayed on the control panel ­ The unit beeps The air conditioner starts cooling, if the room temperature is higher than the selected temperature. If the room temperature reaches the set temperature, the air conditioner stops cooling, but the fan is still operating. 4 Temp. Swing Power To set the fan speed: Press the , or button on the remote control as desired. or Press the button on the unit one or more times until the desired Fan speed(F1, F2 or F3) is displayed. Fan!Speed 5 To control the direction of the air flow, refer to page 11. E-8 Airing Your Room If you want to provide air circulation without cooling, you can use the Fan mode. 1 If necessary, press the Result: (On/Off) button. Remote Control Control Panel The air conditioner starts up in the Cool mode. The unit beeps twice. 2 If the fan speed(F1, F2 or F3) is not displayed on the control panel: Press the button on the remote control or Press the button on the unit one or more times until the fan speed (F1, F2 or F3) is displayed. Result: The unit beeps each time you press the / button. The air conditioner starts up in Fan mode. Mode Cool/Dry/Fan Mode Cool/Dry/Fan You can change modes at any time. The operating time can be set between 1 and 12 hours. Result: Each time you press the Timer button: ­ The time is adjusted by 1 hour and displayed on the control panel ­ The unit beeps The operating time is displayed and decreases automatically to indicate the remaining time. The air conditioner switches off automatically when the operating time reaches zero. You can select the fan speed, temperature and Energy saving mode after setting the On timer and Off timer mode. However, when you change the mode, the On timer and Off timer mode is canceled. To Cancel the Off Timer To cancel the timer, press: Timer on the remote control or unit one or more times until "--" is displayed. or The (On/Off) button on the remote control or unit. E-13 Setting the Sleep Timer The Sleep Timer can be used when you are cooling your room to switch the air conditioner off automatically after 8 hours. The fan will continue to run for a short time after the compressor cycles off. If you would like the air conditioner to run in Dry mode, do not press the E. Saver button. You cannot use the Dry mode in the energy saving mode. 2 To stop the energy saving mode, press the control or Result: E. Saver button on the remote button on the unit again. The fan runs at all times, while the compressor cycles on and off. If you select the Sleep Timer in the Energy Saving mode, the Energy Saving will be cancelled and the air conditioner will start up in the Sleep Timer mode. E-15 Cleaning Your Air Conditioner Be sure to clean the air filter periodically to maintain the air conditioner in the best condition for a long period of time. When cleaning the air conditioner, turn it off and pull out the power plug. 1 Open the front grille by pulling on the tabs of the unit. The removal of the front grille makes it easier to clean the air conditioner. After opening the front grille, lift it up as much as possible, then pull down to release it. [. . . ] Check that the correct operating mode has been selected(Cool). Dust may be blocking the air filter; refer to page 17 for cleaning instructions. Check that there is no obstacle blocking the air flow into or out of the unit. Check that the timer has been programmed correctly; refer to page 12~14. The air conditioner does not operate with the remote control No beep is heard when you press the (On/Off) button on the remote control The air conditioner does not cool The timer is not correctly triggered Odors are permeating the room during air conditioning Ventilate the room. E-18 Technical Specifications Design and specifications ar subject to change without notice. [. . . ]