User manual LG AFR705F

[. . . ] Use the attached RGB cable and RS-232C cable and the shielded LAN cable with this equipment so as to keep interference within the limit of a FCC Class B device. DO NOT LOOK DIRECTLY INTO THE LENS WHEN THE PROJECTOR IS IN THE POWER ON MODE. CAUTION Not for use in a computer room as defined in the Standard for the Protection of Electronic Computer/ Data Processing Equipment, ANSI/NFPA 75. When using the projector in Europe: COMPLIANCE NOTICE This projector complies with the requirements of the EC Directive 2004/108/EC "EMC Directive" and 2006/95/EC "Low Voltage Directive". [. . . ] (Available only for the input signal from the COMPUTER/COMPONENT VIDEO IN 2 terminal. ) Use to select the language used in the menus. Use to reset the settings of the menu (excluding IMAGE CAPTURE, PASSWORD FUNCTION and LANGUAGE) to the factory setting values. CINEMA MODE can be adjusted only when a TV60, TV50, 480i, 576i or 1080i signal is being displayed. When SCART INPUT is set to ON, nothing is output to the external monitor. When SCART INPUT is set to ON, normal computer signals aren't projected. Use a commercially available SCART-Mini D-SUB 15-pin cable when connecting this projector with an AV device equipped with the SCART terminal. Some AV devices equipped with the SCART terminal aren't compatible with this projector. EN-25 Menu operation (continued) 4. SIGNAL menu opt. SIGNAL - RESOLUTION (MEMORIZE) menu opt. SIGNAL - USER menu opt. SIGNAL A U H V SIGNAL AUTO 1024x768 0 0 0 0 RGB 100% OFF OK SIGNAL USER 75. 04 Hz 60. 02 KHz 1024 768 OK OK ? MEMORY CALL RESOLUTION (MEMORIZE ) HORIZ. TRACKING RESOLUTION (MEMORIZE) VERTICAL FREQUENCY HORIZONTAL FREQUENCY HORIZ. LINES EXECUTE CANCEL CLAMP POSITION CLAMP WIDTH VERT. SYNC LPF SHUTTER(U) SHUTTER(L) SHUTTER(LS) SHUTTER(RS) 1 1 AUTO OFF 0 0 0 0 RGB RGB COMPUTER INPUT OVER SCAN HOLD USER ITEM MEMORY CALL SETTING AUTO / MEMORY 1 MEMORY 2 / FUNCTION Use to select the setting of RESOLUTION (MEMORIZE) already saved. Impossible to select if no setting has been saved. Use to adjust the display area of projected image. Use to adjust the image when flagging occurs near the top of the screen. RESOLUTION (MEMORIZE ) 640-1920 VERTICAL FREQUENCY HORIZONTAL FREQUENCY HORIZ. LINES 350-1200 EXECUTE CANCEL HORIZ. TRACKING COMPUTER INPUT OK OK 0-999 0-999 0-31 0-9999 AUTO RGB YCBCR/YPBPR Use to correct solid white or solid black in the projected image. Use to correct solid black in the projected image. Use to adjust the image when its motion doesn't run smoothly. LPF ON / OFF Use to select whether or not to enable the LPF. SHUTTER(U) 0-20 Use to adjust the image when noise appears on the top part of the image. SHUTTER(L) 0-20 Use to adjust the image when noise appears on the bottom part of the image. SHUTTER(LS) 0-20 Use to adjust the image when noise appears on the left half of the image. SHUTTER(RS) 0-20 Use to adjust the image when noise appears on the right half of the image. [. . . ] 1 2 3 4 5 6 7 8 9 Name TXD RXD GND - I/O IN OUT - Pin No. TMDS DATA 2TMDS DATA 2+ TMDS DATA 2 Shield DDC Clock DDC Data TMDS DATA 1TMDS DATA 1+ TMDS DATA 1 Shield - Pin No. 13 14 15 16 17 18 19 20 21 22 23 24 Spec. +5V Power Ground (for +5V) Hot Plug Detect TMDS DATA 0TMDS DATA 0+ TMDS DATA 0 Shield TMDS Clock Shield TMDS Clock+ TMDS Clock- Dimension drawings (unit: mm) Without terminal cover With terminal cover 434 207 103 131. 5 103 371 434 131. 5 207 434 443 434 EN-47 Specifications (continued) Specification of the attached lens (for XL6600LU and XL6500LU) With short throw zoom lens (OL-X500SZ) F No. [. . . ]