User manual LG AGN08FCM1

[. . . ] It may cause product breakdown. If the product was submerged under water, ask the service center for instruction. It may cause fire or an electric shock unless you do that. CAUTION Make sure children or senor citizens use the product under proper observation in order to prevent safety accident. Do not pick the product with a sharp tool. It may cause product breakdown with the damage to its parts. n In-use Do not clean the product with strong cleanser such as solvent. [. . . ] Operation Display Panel Preheat Out door Room Temp Total on Central Run AGN08FCM1 Defrost Slo Lo Med Hi Po 1 2. Temperature Control Button °C °F Cooling Heating Auto Dry Fan 2 TEMP ROOM TEMP FAN SPEED TEMP 3 4 5. Room Temperature Check Button 5 Each function will be shown on the display panel for three second or so when the power is applide at first. Accessory Connecting Cable (1EA) Fixing Screw (2EA) User / Installation Manual Installation Paper Owners & Installation Manual 5 Wired remote controller switch information Wired remote controller switch information Group Control 2 1 Ceiling Height/Default E. S. P 3 2 1 SWHI Group control switch SWGR 1. For group control/Slave use Ceiling height selection switch 1. High ceiling Product selection switch 1. Heat Pump product Select Product 2 1 SWPD Indoor temperature sensor selection switch 1. Use the temperature sensor on the remote controller. Use the temperature sensor on the product. Use the sensors on the product and remote controller. Room Temp. Sensing 321 SWTH · When changing the product selection switch and group control switch, the power must be reconnected to reflect the changes. · The central control could operate inappropriately depends on indoor unit type, when the remote controller is set as slave. 6 Simple Wired Remote Controller Installation Method Installation Method 1 Put the installation paper on the place and determine the position and height of the fixing screws of the wired remote controller. · You cannot control the group as shown in the right for some products. GND Signal wire 12V BYR PQRCUCS0C GND Signal wire 12V BYR PQRCUCS0C Defrost Slo Lo Med Hi Po Preheat Out door Room Temp Total on Central Run Defrost Slo Lo Med Hi Po Preheat Out door Room Temp Total on Central Run Cooling Heating Auto Dry Fan Cooling Heating Auto Dry Fan TEMP MODE FAN SPEED TEMP MODE TEMP FAN SPEED TEMP MASTER SLAVE <When simultaneously connecting 2 sets of wired remote controller> j Some products do not use 'Group control'. For more detail, refer to the product manual. 8 Simple Wired Remote Controller Necessary functions before using Necessary functions before using Trial Operation The trial operation is to check the installation status of the product. The temperature will not be controlled during trial operation. Instead the product will operate in several modes such as cooling, strong wind, comp-on. ENGLISH 1 AGN08FCM1 If you want to set the trial operation mode, press the Room Temperature button and the fan speed button same time for three seconds. Defrost Preheat Out door Room Temp" Total on" Central Run 2 TEMP ROOM" TEMP FAN" SPEED TEMP Then the product will begin the trial operation and the display will be like as shown on left side picture. 3 4 If you want to cancel the trial operation mode, just press the On/Off button. The trail operation will shut down automatically after 18 minutes and system will go to the standby mode. * This function might not be available for Multi Product like Multi V system. Owners & Installation Manual 9 Necessary functions before using Celsius/Fahrenheit Switching 1 AGN08FCM1 If you want to change the temperature unit as the Celsius or Fahrenheit, press the Temperature control button( ) and the Fan speed button same time for three seconds to enter the setting Mode. Defrost Preheat Out door Room Temp Total on Central Run 2 TEMP ROOM TEMP FAN SPEED TEMP Press the temperature control button to change the unit. Ex) Setting unit as Fahrenheit. Defrost Preheat Out door Room Temp Total on Central Run Defrost Preheat Out door Room Temp Total on Central Run <Setting as Celsius> <Setting as Fahrenheit> 3 After setting, press the Temperature control button( ) and the Fan speed button same time for three seconds to exit the setting Mode. The system will automatically release without input after 60 seconds. Defrost Preheat Out door Room Temp Total on Central Run 10 Simple Wired Remote Controller Necessary functions before using Setting the Central-Control Address Please set the address while using the central controller. You don't need to set address if you don't use central controller. ENGLISH 1 AGN08FCM1 If you want to set the address on the display panle, press both temperature control buttons (s/t) same time for three seconds. Defrost Preheat Out door Room Temp Total on Central Run 2 3 Press the temperature-increasing button to change the group number. Press the temperature-decreasing button to change the indoor unit number. As shown on the left side panel, it displays 23. : 3 Set the address by pressing both temperature control buttons again (s/t) at the same time for three seconds. TEMP ROOM TEMP FAN SPEED TEMP TEMP MODE FAN SPEED TEMP Group No. Indoor Unit No. · If you connect the indoor unit to the central controller, you should set the network address of the indoor unit so that the central controller could recognize it. [. . . ] It is for the convenience of installation. (16~30°C) Defrost Preheat Out door Room Temp Total on Central Run TEMP TEMP A click of the button will increase the desired temperature by 1°C or 2°F. A click of the button will decrease the desired temperature by 1°C or 2°F. * If the desired temperature is set lower than the current room temperature, the heating function will not begin. TEMP ROOM TEMP FAN SPEED TEMP 3 If you want to change mode during the operation, the operation mode will be changed by Central Controller. 4 If you press On/Off button again, the heating operation will stop. 14 Simple Wired Remote Controller How to use the Mode Selection Button Auto-Operation ENGLISH 1 AGN08FCM1 Set the operation mode to auto-operation by central controller after pressing the On/Off button. Defrost Preheat Out door Room Temp" Total on" Central Run 2 When the room temperature is lower than the desired temperature: Heating Operation starts [For Heat Pump Models only] When the room temperature is higher than the desired temperature: Cooling Operation starts TEMP ROOM" TEMP FAN" SPEED TEMP 3 If you want to change Mode during the operation, the operation mode will be changed by central controller. h This auto-operation is not related to "Auto Change Over" function. Owners & Installation Manual 15 How to use the Mode Selection Button Dry(Dehumidification) Operation Dry(Dehumidification) by lowering temperature slightly 1 AGN08FCM1 If you want to start the dry operation, press On/Off button. The dry operation can be set from Central Controller only. [. . . ]