User manual LG AGW12AJG1

[. . . ] Model Number : Serial Number : LG Electronics U. S. A. , Inc. Warning/Caution Warning/Caution WARNING/CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING/CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING/CAUTION: TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. POWER CORD POLARIZATION: CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. ATTENTION: POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU'AU FOND. NOTE TO CABLE/TV INSTALLER: This reminder is provided to call the CATV system installer's attention to Article 820-40 of the National Electric Code (U. S. A. ). [. . . ] Use the D / E buttons to view the shows. Remind Conflict A conflict message appears for the following reasons: · a show set with an Auto-Tune Reminder has the same start time as an existing Auto-Tune Reminder. · If you are using a cable box, a show set with an AutoTune Reminder overlaps with a Recording already scheduled. Select one of these options: W auto-tune anyway - this show will override an existing show set to auto-tune W proceed, no auto-tune - set the show as a Reminder but do not auto-tune W don't set this reminder - cancel the Reminder 56 DLP Projection TV Operation Operation Turning the TV On * In this manual, the OSD (On Screen Display) may be different from your TV's because it is just an example to help you with the TV operation. Turning on the TV just after installation 1. At this moment, the TV is switched to standby mode. Press the TV INPUT, TV/VIDEO, CH (D / E), Number (0 ~ 9) button on the remote control or press the CH (D / ton on the TV front panel and then the TV will switch on. E) but- Turning on the TV (power cord is still connected) 1. If the TV was turned off with indicators on the TV · Check the power cable. If the TV was turned off with the remote control and the POWER button on the TV · Press the POWER button on the TV or press the POWER, TV/VIDEO, CH (D / button on the remote control to turn the TV on. E), Number (0 ~ 9) Notes: · If you intend to be away on vacation, disconnect the power plug from the wall power outlet. · The TV Guide On Screen and any CableCARDTM Software upgrades work while the TV is in standby · mode. If you pull the power plug cord the TV Guide On Screen will not update its listings and no ··· · CableCARDTM Software upgrades will occur. · After turning on the TV, it could take up to a week for the TV Guide On Screen system to receive full list· ings data. Owner's Manual 57 Operation TV Setup On-screen Menus Language Selection - The menus can be shown on the screen in the selected language. Press the MENU button and then use menu. Use D / E / F / G button to select a channel and then use the ENTER button to add or delete it. Press FAV to add or delete the channel to the Favorite List. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. Note: · When a cable box connects to the physical channel 2, 3, or 4 in TV Guide On Screen Setup, cable channels(CATV or CADTV) will not be editable by Channel Edit. Instead, use the cable box's Channel Edit if available. DTV Signal Strength - Shows how strong your DTV signal is and whether you need to adjust your antenna or digital cable input. The higher the signal strength, the less likely you are to experience picture degradation. - DTV Signals: When input signals are DTV, CADTV, this function is available. View the on-screen signal strength monitor to see the quality of the signal being received. · You can also check the DTV Signal strength with the SETUP menu. 60 DLP Projection TV Operation Channel Label Setup - Choose preset labels for your channels. - If a channel label is provided on the signal from the broadcasting station, the TV displays a short name for a DTV channel - even if you didn't preset a label for the channel. 1. Use the CH D /E D /E button to select the SETUP menu. D /E button to select Channel Label. 3. You will now see a screen filled with Labels and a preview screen. [. . . ] Before you call for warranty service, check your operating guide ­ you may avoid a service call. LG®Brand Customer Interactive Center P. Box 240007 201 James Record Road Huntsville, Alabama 35824 ATTN: CIC Telephone number: 1-800-243-0000 This number is a toll-free number Follow menu prompts when the call is answered Web address: www. lgservice. com Telephone Center Hours of Operation: 24 hours a day, 365 days per year Service for your LG®Brand Rear Projection Television is provided through LG Electronics Alabama, Inc. , the authorized LG®Brand Service Center for the United States. LG®Brand DLP Rear Projection Televisions are marketed and distributed in the United States by LG Electronics Corporation, 2000 Millbrook Drive, Lincolnshire, IL 60069. LG® Brand DLP Rear Projection Television U. S. [. . . ]