User manual LG AP-Z488TC0

[. . . ] n Incorrect operation due to ignoring instruction will cause harm or damage. The seriousness is classified by the following indications. ENGLISH WARNING CAUTION This symbol indicates the possibility of death or serious injury. This symbol indicates the possibility of injury or damage. n Meanings of symbols used in this manual are as shown below. Be sure not to do. Be sure to follow the instruction. WARNING n Installation Do not use a defective or underrated circuit breaker. [. . . ] · Be sure that there are no obstructions between the remote control and the signal receptor. · Do not drop or throw the remote control. Press the Operation Mode Selection Button. Press the Soft Dry Operation Button on the remote controller. A/CL 3 Set the temperature lower than the room temperature. The temperature can be set within a range of 18°C~30°C by 1°C. To raise the temperature To lower the temperature During softy Dry Operation · The indoor fan speed is automatically set to low and can be set fan speed. 12 Floor Standing-Type Air Conditioner Operating Instructions ENGLISH Heating Operation Mode(Heat Pump Model) 1 Press the Start/Stop Button. 2 Select heating Operation. Press the Operation Mode Selection Button. Press the heating Operation Button on the remote controller. A/CL 3 Set the temperature upper than the room temperature. The temperature can be set within a range of 16°C~30°C by 1°C. To raise the temperature To lower the temperature 4 Set the Fan Speed. q Each time the Button is pressed, the Fan Speed mode is shifted. Owner's Manual 13 Operating Instructions Auto Operation Mode(Cooling Model Only) 1 Press the Start/Stop Button. 2 Select Auto Operation. Press the Operation Mode Selection Button. Press Auto Operation Button. A/CL 3 Set the temperature upper or lower than the standard temperature. The temperature can be set within a range of by 1 level. Cold Cool Proper Warm Hot (This indication will be shifted to the initial Auto Mode Display state after 4 seconds. ) To raise the temperature. (When you feel too cool or cold) To lower the temperature. (When you feel too warm or hot) During Auto Operation · It is impossible to switch the indoor fan speed because of being already set to the best conditioner by fuzzy rule. 14 Floor Standing-Type Air Conditioner Operating Instructions ENGLISH Electric Heater Operation Mode(Heat pump & Electric heater product only) 1 Press the Start/Stop Button. 2 Select heating Operation by pressing the Opertion Mode Selection button. Press the Heater Operation Button on the remote controller. A/CL 3 Set the temperature upper than the room temperature. The temperature can be set within a range of 16°C~30°C by 1°C. To raise the temperature To lower the temperature 4 Set the Fan Speed. q Each time the Button is pressed, the Fan Speed mode is shifted. Owner's Manual 15 Operating Instructions OFF Timer Setting Procedure(OFF TIMER Setting, or CANCEL) 1 Press the Start/Stop Button. 2 3 Select Function. Press the Timer Button. A/CL · If you press the button, the selected off timer is displayed as follows; · If you select ` ', the Off Timer function will be cancelled. 4 When you finish the Off Timer setting, the Timer indicator lights off. After 4 seconds 5 During off-timer operation if you press the Timer Button, the rest time will be displayed. 16 Floor Standing-Type Air Conditioner Operating Instructions ENGLISH Plasma Air Purifying Operation Procedure 1 Air Purifying Operation only Press the Plasma Air Purifying Operation Start/Stop Button. 1 A/CL (Operation will start when the button is pressed, and stop when the button is pressed again. ) 2 Select Fan speed. The display shows low fan speed at the initial condition. Low Mid · You can operate the Plasma Air Purifying under the unit operation of cooling, heating, soft dry or Auto mode. 2 Air Purifying Operation with Cooling or any other Operateion. 1. Press the Plasma Air Purifying Operation ON/OFF Button. Set the fan speed. Owner's Manual 17 Operating Instructions Child Lock Operation Procedure 1 Press the fan speed button and High temperature setting buttons simultaneously for 3 conds. The unit will respond with beep. After 3 second, it will shift After 3 seconds, it will shift 2 During Child Lock Operation Whenever you press any Button on Display Panel, it will immediately display " ", which means Display panel is Locked. All the Button on the indoor unit Display panel will not work. But the Button on the remote controller will work. 3 For releasing child lock Operation Press the fan speed button and High temperature setting buttons simultaneously for 3 conds. The unit will respond with beep, Child Lock Operation will removed. After pressing the buttons it will shift immediately After 3 seconds, it will shift Auto restart In case the power comes on again after a power failure, Auto Restarting Operation is the function to operate procedures automatically to the previous operating conditions. 18 Floor Standing-Type Air Conditioner Maintenance and Service Maintenance and Service CAUTION: Before performing any maintenance, turn off the main power to the system. ENGLISH During the season Cleaning of the air filters. [. . . ] In order to prevent this, the airflow will not begin until it is sufficiently warm. · The room may have been very hot when the room air conditioner was first turned on. · Has the temperature been set incorrectly?· Are the indoor unit's air inlet or outlet vents obstructed? [. . . ]