User manual LG APNZ286R20

[. . . ] ENGLISH ITALIANO ESPAÑOL FRANÇAIS DEUTSCH OWNER'S MANUAL AIR CONDITIONER Please read this manual carefully before operating your set and retain it for future reference. TYPE : FLOOR STANDING The equipment complies with requirements of the Technical Regulation, in terms of restrictions for the use of certain dangerous substances in electrical and electronic equipment. www. lg. com P/NO : 3828A22014N Floor Standing- Type Air Conditioner Owners Manual TABLE OF CONTENTS FOR YOUR RECORDS Safety Precautions. . . . . . . . . . . . . . . . . 3 Write the model and serial numbers here: Model # Serial # Prior to Operation . . . . . . . . . . . . . . . . . . 6 You can find them on a label on the side of each unit. Dealer's Name Date Purchased Indtroduction . . . . . . . . . . . . . . . . . . . . . . . . . . 6 n Staple your receipt to this page in the event you need it to prove date of purchase or for warranty issues. Operating Instructions. . . . . . . . . . . 5 READ THIS MANUAL Inside you will find many helpful hints on how to use and maintain your air conditioner properly. Just a little preventive care on your part can save you a great deal of time and money over the life of your air conditioner. You'll find many answers to common problems in the chart of troubleshooting tips. [. . . ] How to mount onto a wall Use the screws to secure the holder to the wall or attach the holder side of indoor unit. · Please keep it on the right side of indoor unit. When opening When closing 2. To insert the remote control to the holder. Insert Pull How to insert batteries 1. Remove the cover from the back of the remote controller. · Slide the cover according to the arrow direction. · Be sure that the (+) and (-) directions are correct. · Be sure that both batteries are new. · Slide the cover into back position. · Do not use rechargeable batteries such batteries as different from standard dry cells in shape, dimensions, and performance. · Change the batteries with a new one if the remote control does not work properly after using for an extended length of time. 10 Floor Standing-Type Air Conditioner Operating Instructions ENGLISH Cooling Operation Mode 1 Press the on/off button. (or touch the anyplace of touch panel and touch the on/off key) TURBO-Z SET ROOM TURBO-Z TEMP. ON/OFF PLASMA 2 Select Cooling Operation. Press the Cooling Operation Button on the remote controller (or Touch the Cooling Operation key on the touch panel) SET A/CL TEMP. TURBO-Z ON/OFF PLASMA 3 Set the temperature lower than the room temperature. The temperature can be set within a range of 16°C~30°C by 1°C. SET To raise the temperature To lower the temperature TURBO-Z TEMP. ON/OFF PLASMA 4 When you finish the temperature setting. After 4 seconds ROOM TURBO-Z SET TEMP. TURBO-Z ON/OFF PLASMA TEMP. ON/OFF PLASMA 5 Set the Fan Speed. Low TURBO-Z SET TEMP. TURBO-Z ON/OFF PLASMA Mid High q Each time the Fan Speed Button is pressed (or fan speed key is touched), the Fan Speed mode is shifted in the arrow direction. Owner's Manual 11 Operating Instructions Soft Dry Operation 1 Press the on/off button. (or touch the anyplace of touch panel and touch the on/off key) TURBO-Z SET ROOM TURBO-Z TEMP. ON/OFF PLASMA 2 Select Soft Dry Operation Press the Soft Dry Operation Button on the remote controller (or Touch the Soft Dry Operation key on the touch panel) SET A/CL TEMP. TURBO-Z ON/OFF PLASMA 3 Set the temperature lower than the room temperature. The temperature can be set within a range of 16°C~30°C by 1°C. To raise the temperature To lower the temperature SET TEMP. TURBO-Z ON/OFF PLASMA During softy Dry Operation · The indoor fan speed is automatically set to low and can be set fan speed. Low TURBO-Z ROOM TURBO-Z TEMP. ON/OFF PLASMA Mid High 12 Floor Standing-Type Air Conditioner Operating Instructions ENGLISH Turbo-Z cooling Operation 1 Press the on/off button. (or touch the anyplace of touch panel and touch the on/off key) TURBO-Z SET ROOM TURBO-Z TEMP. ON/OFF PLASMA 2 Press the Turbo-Z Cooling button to operate the speed cooling mode and the unit will operate in super high fan speed on cooling mode. To cancel the Turbo-Z Cooling mode, press the Turbo-Z Cooling button or the Auto Swing Direction Control Button (Up & Down, Left & Right) and the unit will operate in Med Fan speed mode on cooling mode. TURBO-Z SET TEMP. TURBO-Z ON/OFF PLASMA 3 To cancel the Turbo-Z Cooling mode, press the Turbo-Z Cooling button again or the Auto Swing Direction Control Button (Up & Down, Left & Right) and the unit will operate in Med. Fan speed on cooling mode. TURBO-Z A/CL NOTICE o During the Turbo-Z Cooling function at any moment, the A/C starts to blow the cool air at extremely high speed setting the room temp. It is especially used to cool the room temp. In heat pump mode or neuro fuzzy mode however, the Turbo-Z Cooling function is not available. o In order to return to the normal cooling mode from the Turbo-Z Cooling mode, you just press either the operation mode selection button, airflow volume selection or temp. setting button or the Turbo-Z Cooling button again. Owner's Manual 13 Operating Instructions Heating Operation Mode(Heat Pump & Heater, Heat Pump Model) 1 Press the on/off button. (or touch the anyplace of touch panel and touch the on/off key) TURBO-Z SET ROOM TURBO-Z TEMP. ON/OFF PLASMA 2 Select Heating Operation Press the Heating Operation Button on the remote controller (or Touch the Heating Operation key on the touch panel. ) SET A/CL TEMP. TURBO-Z ON/OFF PLASMA 3 Set the temperature upper than the room temperature. The temperature can be set within a range of 16°C~30°C by 1°C. To raise the temperature To lower the temperature SET TEMP. TURBO-Z ON/OFF PLASMA 4 Set the Fan Speed. TURBO-Z ROOM TURBO-Z TEMP. ON/OFF PLASMA Low High q Each time the Button is pressed, the Fan Speed mode is shifted. 14 Floor Standing-Type Air Conditioner Operating Instructions ENGLISH Electric Heater Operation Mode(Heater, Heat Pump Model) 1 Press the on/off button. (or touch the anyplace of touch panel and touch the on/off key) TURBO-Z SET ROOM TURBO-Z TEMP. ON/OFF PLASMA controller 2 Press the Heating & E/Heater Operation Button on the remotepanel) (or Touch the heating & E/Heater Operation key on the touch Select Heating + E/Heater Operation. SET TEMP. A/CL A/CL ON/OFF PLASMA TURBO-Z 3 Set the temperature lower than the room temperature. The temperature can be set within a range of 16°C~30°C by 1°C. To raise the temperature To lower the temperature SET TEMP. TURBO-Z ON/OFF PLASMA 4 Set the Fan Speed. TURBO-Z Low SET TEMP. TURBO-Z ON/OFF PLASMA High * Each time the Button is pressed, the Fan Speed mode is shifted. Owner's Manual 15 Operating Instructions Auto Operation Mode(Cooling Model Only) 1 Press the on/off button. (or touch the anyplace of touch panel and touch the on/off key) TURBO-Z SET ROOM TURBO-Z TEMP. ON/OFF PLASMA 2 Select Auto Operation Press the Auto Operation Button on the remote controller (or Touch the Auto Operation key on the touch panel) SET A/CL TEMP. TURBO-Z ON/OFF PLASMA 3 Set the temperature upper or lower than the standard temperature. The temperature can be set within a range of by 1 level. SET TEMP. TURBO-Z ON/OFF PLASMA Cold Cool Proper Warm Hot (This indication will be shifted to the initial Auto Mode Display state after 4 seconds. ) To raise the temperature (When you feel too cool or cold) To lower the temperature (When you feel too warm or hot) During Auto Operation · It is impossible to switch the indoor fan speed because of being already set to the best conditioner by fuzzy rule. 16 Floor Standing-Type Air Conditioner Operating Instructions ENGLISH Energy Saving Mode(Cooling & Soft Dry Operation Only) 1 Press the on/off button. (or touch the anyplace of touch panel and touch the on/off key) TURBO-Z SET ROOM TURBO-Z TEMP. ON/OFF PLASMA 2 Press the Energy Operation Button on the remote controller (or Touch the Energy Saving Operation key on the touch panel) Select Energy Saving Operation TURBO-Z SET TEMP. TURBO-Z ON/OFF PLASMA 3 To cancel the Energy Saving mode. [. . . ] This is caused by water being picked up by the fan on rainy days or in highly humid conditions. This feature is designed to help remove moisture in the air and improve cooling efficiency. This is caused by the compressor cycle starting and stopping. · You see water dripping from the rear of the unit. [. . . ]