User manual LG ARNU07GSPD1

[. . . ] · The following safety cautions are provided to prevent unexpected dangers or losses. WARNING : If the user does not follow the mandatory items, it may result in serious injury or death. CAUTION : If the user does not follow the mandatory items, it may cause personal injury or property damage. : Warning and Caution are to call the user's attention to the possible danger. Read and follow them carefully in order to prevent a safety accident. [. . . ] 16 Wide Wired Remote Controller Installation instruction Installer Setting -Static Pressure Setting This function is applied to only duct type. Setting this in other cases will cause malfunction. ENGLISH button for 1 Press the installer 4 seconds to enter setting mode until timer segment display "01:01". 2 Repeat pressing Function code 06. Function Code button to select Pressure 3 Select static pressure by pressing button. (01:V-H, 02:F-H, 03:V-L, 04:F-L) 4 Press release. button to save or 5 Press willbutton to exit orexit system automatically after 25 seconds without any input. <Static Pressure Setting Table> Pressure selection 01 02 03 04 F-L F-H V-L V-H Function Zone state Fixed Fixed Variable Variable ESP standard value Low High Low High Owner's & Installation Manual 17 Installation instruction Installer Setting-Group Setting This function is only for group control operation. Please don't set this function in case of non-group control. 4 seconds 1 Press thebutton for setting to enter installer mode until timer segment display "01:01". 2 Repeat pressing Function code 07. Function Code button to select Master/Slave value Ex) 'Master' Setting 3 Select Master/ Slave by pressing button. (00: Slave, 01: Master) 4 Press button to save or release. 5 Press willbutton to exit orexit system automatically after 25 seconds without any input. 18 Wide Wired Remote Controller Installation instruction Installer Setting -Mode Override Setting In case of More than 2 indoor units connected to 1 outdoor unit, they are assigned as Master indoor and Slave indoor. (the setting code for this function is not displayed with un-equipped unit). ENGLISH 4 seconds 1 Press thebutton for setting to enter installer mode until timer segment display "01:01". 2 Repeat pressing Function code 08. Function Code button to select Master/Slave Ex) Override 'Master' Setting 3 Select Master/ Slave by pressing button. (00: Slave, 01 : Master) 4 Press button to save or release 5 Press willbutton to exit orexit system automatically after 25 seconds without any input. Owner's & Installation Manual 19 Installation instruction Installer Setting-Dry Contact Mode Setting This function allows the Dry contact-indoor unit operate under Auto Run mode or Manual mode with remote controller. button for 1 Press the installer 4 seconds to enter setting mode until timer segment display "01:01". 2 Repeat pressing button to select Function code 09. Function Code Dry Contact setting value Ex) Setting Dry Contact Mode 'ON' contact 3 Select Drybutton. setting by pressing (00: OFF, 01: ON) 4 Press button to save or release. 5 Press willbutton to exit orexit system automatically after 25 seconds without any input. * Please refer to dry contact manual for more details. 20 Wide Wired Remote Controller Installation instruction Installer Setting-Zone State Setting This function is only available on some products. It is possible to setup Variable or Fixed option for Zone State of indoor. The initial setting is 'Variable' ENGLISH 4 seconds 1 Press thebutton for setting to enter installer mode until timer segment display "01:01". 2 Repeat pressing Function code 11. Function Code button to select Zone State fixing mode Ex) Setting Zone State as 'Fixed'. mode by pressing (01: Variable, 02: Fixed) 4 Press button to save or release. 5 Press will button to exit or system automatically exit after 25 seconds without any input. Owner's & Installation Manual 21 Installation instruction Installer Setting-Celsius / Fahrenheit Switching This function is used for switching the display between Celsius and Fahrenheit. (Optimized only for U. S. A) button for 1 Press the installer 4 seconds to enter setting mode until timer segment display "01:01". 2 Repeat pressing Function code 12. Function Code button to select conversion mode value Ex) Fahrengeit Setting 3 Select Temperature unit mode by pressing button. (01: Celsius, 02: Fahrenheit) 4 Press button to save or release. 5 Press willbutton to exit orexit system automatically after 25 seconds without any input. Whenever press degrees. button in Fahrenheit mode, the temperature will increase/drop 2 22 Wide Wired Remote Controller Installation instruction Installer Setting -Optional Function Setting For the optional product such as PLASMA PURIFICATION/DEHUMIDIFIER/ ELECTRIC HEATER and VENTILATION, ELEVATION GRILL. It is possible to set the items are installed or not 4 seconds 1 Press thebutton for setting to enter installer mode until timer segment display "01:01". ENGLISH 2 Repeat pressing function code. button to select (20: PLASMA PURIFICATION, 21: DEHUMIDIFIER, 22: ELECTRIC HEATER, 23:VENTILATION KIT, 24: ELEVATION GRILL) Function Code Existing condition 3 Select existing condition of each mode by pressing button. button, 2 Whenever press be displayedthe room temperature will within 5 seconds. After 5 seconds, it turns to display the desired temperature. Because of location of remote controller, the real room temperature and the this displayed value can be different ENGLISH Owner's & Installation Manual 29 Owner's instruction Ariflow Setting We can simply adjust the desired airflow rate buttons 1 Press direction. to set the desired airflow · ¡ (NONE) ¡ ¡ ¡ · Display of these lists depends on products function. NONE : Released swirl Please refer to the manual of product. <Ariflow Setting Table> Symbol Swril : vane paired opend cross Up·Down : Vane move from up to down automatically and continuously Left·Right : Vane move from left to right automatically and continuously Description 30 Wide Wired Remote Controller Owner's instruction Sub function : Plasma Purification 1 Repeat pressing until icon flash. button ENGLISH 2 Operate or cancel Plasma Purification function by pressing ( button. icon appears/disappears on display part up to selection ) button 3 After setting, press to exit. When turn the machine off, Plasma function is off (And also off when restart indoor) In case of such model that has no Plasma sub function, it doesn't appear when pressing button. Sub function : Humidifier 1 Repeat pressing until icon flash. button 2 Turn on/off HUMIDIFIER byicon pressing button (The will be displayed in case of SETTING option and disappear in reverse case . ) of non-selection, 3 In casewithin 10 seconds press button to exit the setting screen. Details: When turn the Off the product, HUMIDIFIER function is off (And also off when restart indoor) In case of such model that has no HUMIDIFIER sub function, it doesn't appear when pressing button. Owner's & Installation Manual 31 Owner's instruction Sub function : Electric Heater 1 Repeat pressing until icon flash. button 2 Turn on/off ELECTRIC HEATER by pressing button (the icon will be displayed in case of SETTING option and disappear in reverse case . ) of non-selection, press 3 In casewithin 10seconds to exit button the setting screen. Detail - ELECTRIC HEATER function is only available under HEATING mode. - While operate ELECTRIC HEATER together with HEATING mode, ELECTRIC HEATER is off when turn the machine off (And also off when restart HEATING mode By both wireless or wired remote controller) - Whenever changing operation mode while running ELECTRIC HEATER together with HEATING mode, ELECTRIC HEATER is off. - in case of such model that has no ELECTRIC HEATER sub function, it doesn't appear when pressing button. - ELECTRIC HEATER operation is also active by wireless remote controller. 32 Wide Wired Remote Controller Owner's instruction Sub function : Fan Auto button 1 Repeat pressing flash. until the icon ENGLISH or 2 Operate by cancel Fan Auto function pressing button. ( icon appears/disappears on display part up to selection. [. . . ] (In case of exit with incomplete information, it will return to the previous setting ) Owner's & Installation Manual 39 Owner's instruction Programming : Setting Simple Reservation In case of there is not any reservation setup on system, it is possible to make a SIMPLE reservation on indoor unit. 1 Press button to enter the Programming mode. (the segment flashing) Ex) Setting Simple Reservation time as '3'. to adjust reservation 3 Press button to finish setting. 4 Adjusting the reservation time after finish reservation setting will release the previous one. If the indoor is ON, we can make the reservation for turning OFF. In reserve, if the indoor is OFF, we can set the timer for turning ON. The reservation time is from 1 to 7 hours. 40 Wide Wired Remote Controller Owner's instruction Programming : Setting Sleep Reservation This function is able to turn off Air conditioner when sleeping or after some hours. ENGLISH 1 Press button to enter the Programming mode. Ex) Setting Sleep Reservation time as '3'. [. . . ]