User manual LG B30AHV

[. . . ] If any items are missing, contact your dealer. User's Guide/Cards 15-pin D-Sub Signal Cable (To set it up, this signal cable may be attached to this product before shipping out. ) and Power Cord (Depending on the country) Lan cable and EMI Core (These items are not included for all models. ) IMPORTANT This accessories may look different from those shown here. User must use shielded signal interface cables (D-sub 15 pin cable, LAN cable) with ferrite cores to maintain standard compliance for the product. Important Precautions This unit has been engineered and manufactured to ensure your personal safety, however improper use may result in potential electrical shock or fire hazards. In order to allow the proper operation of all safeguards incorporated in this display, observe the following basic rules for its installation, use, and servicing. On Safety Use only the power cord supplied with the unit. In case you use another power cord, make sure that it is certified by the applicable national standards if not being provided by the supplier. [. . . ] Place the monitor with its front facing downward on a cushion or soft cloth. Assemble the Stand Base into the Stand Body. Be sure don't pull out the Stop Pin and make the Stand Base direction as shown. Stand Body Side Stop Pin FRONT Stand Base 3. Make the monitor stand , then pull out the Stop Pin. Warning: The tape and locking pin may only be removed from those monitors equipped with a standing base when the base is pulled up. Otherwise, you may be injured by the protruding sections of the stand. pull out the stop pin Stop Pin Stop Pin Important This illustration depicts the general model of connection. Your monitor may differ from the items shown in the picture. Do not carry the product upside down holding only the stand base. The product may fall and get damaged or injure your foot. A4 Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Positioning your display 1. Adjust the position of the panel in various ways for maximum comfort. Tilt Range: -5°~ 18° -5° 18° Height Range: maximum 4. 33 inch (110. 0 mm) 110. 0 mm First, remove the locking pin. Ergonomic It is recommended that in order to maintain an ergonomic and comfortable viewing position, the forward tilt angle of the monitor should not exceed 5 degrees. A5 Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Positioning your display Using the cable holder 1 2 3 A6 Connecting the Display Using the Computer NOTE This is a simplified representation of the rear view. This rear view represents a general model; your display may differ from the view as shown. 1. A Connect D-sub(RGB Analog) Cable (PC) B Connect D-sub(RGB Analog) Cable (Mac) Analog signal X-PORT D-sub Wall-outlet type A B Mac adapter (This item must be purchased separately. ) For Apple Macintosh use, a separate plug adapter is needed to change the 15 pin high density (3 row) D-sub VGA connector on the supplied cable to a 15 pin 2 row connector. 2. Press button on the front switch panel to turn the power on. PC spec : The host PC operating system can be Windows Server 2003 R2 SP2(Standard or Enterprise Edition, 32-bit). Notice - To achieve the best PC performance, up to six users are recommended for one PC. If there are seven or more users, performance may be degraded depending on the environment and the PC's specifications. - Check if the PC supports Windows Server 2003 before purchasing it. A host PC should have the following specifications: 1. Minimum - CPU : Dual core processor at 3. 0 GHz or higher (i. e. : Intel Core 2 Duo or AMD Athlon X2) - RAM : 2 GB of system memory or higher 2. Recommend - CPU : Quad core processor at 2. 66 GHz or higher (i. e. Intel Core 2 Quad or AMD Phenom X4) - RAM : 4 GB of system memory 3. Internet access speed may be different depending on the network environment. Restrictions : Using this network monitor for the following purposes may cause screen disruption or slower PC operation. [. . . ] G Do you see a "CHECK SIGNAL CABLE" message on the screen?· This message appears when the signal cable between your PC and your display is not connected. Check the signal cable and try again. Do you see a "OSD LOCKED" message on the screen? G Do you see "OSD LOCKED" when you push MENU button?· You can secure the current control settings, so that they cannot be inadvertently changed. [. . . ]